Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Land Pride Dateigröße: 2.66 mb Dateiname: Unterrichtssprache:

1. Clean the cutter as necessary. 2. Check the blades for wear and replace if necessary, see "Service Cutting Blades" on page 17. 3. Inspect the cutter for loose, damaged or worn parts and adjust or replace as needed. 4. Lubricate as noted in "Lubrication Points" on page 19. 5. Store the cutter inside if possible for longer cutter life. 6. Repaint parts where paint is worn or scratched to prevent rust. Ask your dealer for Aerosol Land Pride Beige touch-up paint #821-011C. 23788 19 Section 4: Maintenance and Lubrication 12/28/05 RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters 312-556M Land Pride Table of Contents Gauge Wheel Spindle Tube Type of Lubrication: Grease Quantity = 6 pumps 16344 Gauge Wheel Hub The gauge wheel hub is equipped with a relief hole located directly opposite the grease fitting. The relief hole releases pressure from inside the hub casting when it is greased. The hub should be greased until grease purges from the relief hole. Type of Lubrication: Multipurpose Grease Quantity = Until grease purges from the relief hole 16278 Gearbox Check oil level in the gearbox by removing the side plug in the gearbox case. If the oil level is low, remove the top plug in the gearbox case and fill with EP90 oil until oil flows from the side port of gearbox case. Reinstall plugs and tighten. ype of Lubrication: EP90 Oil Quantity = fill until oil flows from the side port of gearbox case. NOTE: Do not overfill! Cutter should be level when checking oil. 16345 Lubrication Points 50 Multi-purpose spray lube Multi-purpose grease lube Intervals in hours at which lubrication is required Lubrication Legend Multi-purpose oil lube 8 Hours 24 Hours 8 Hours 20 Section 4: Maintenance and Lubrication RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters 312-556M 12/28/05 Table of Contents Land Pride Driveline Profiles Quantity = Clean & coat the inner tube of the driveline with a light film of grease and then reassemble. Driveline U-Joints Type of Lubrication: Grease Quantity = 6 pumps 13755 14618 Driveline Shield Bearings Type of Lubrication: Grease Quantity = 6 pumps 13755 8 Hours 8 Hours 20 Hours Land Pride Table of Contents Section 5: Specifications & Capacities RCR15 Series Rotary Cutters RCR1542 RCR1548 RCR1560 RCR1572 Hitch Category l Working Width 42” 45 1/2” 57" 69" Overall Width 47 1/2” 50” 62" 74" Overall Length (Including Tailwheel) 86” 90” 96" 108“ Machine Weight (with Front Guard) 432# 475# 495# 614# Blade Tip Speed 11,459 fpm 13,090 fpm 16,363 fpm 14,874 fpm Deck Material Thickness 12 Gauge Gearbox Rating 30 HP 40 HP Horsepower Rating 15-50 20-50 25-50 Cutting Height 1 3/4” - 11 1/2” 1” - 9” 1” - 9” Cutting Capacity Grass Safety Guards Rubber (front) or Chain (front or rear) Skids 1/4” X 2” Weld on Deck Height (Bottom of Deck to Bottom of Skid Shoe) 7 1/4” Blades 1/2” x 3" Heat Treated Alloy Steel Free-Swinging Blades Stump Jumper Round Pan 10 ga. x 24” Round Pan 10 ga. x 24” Round Pan 10 ga. x 24” Round Pan 10 ga. x 24” Driveline ASAE Category 3 Driveline Safety Protection Standard 1/2” Center Shearbolt protection Optional - Center Bolt 2 plate Slip Clutch Gearbox (Speed up beveled gears) 540 rpm PTO Driven Gearbox 1:1.93 Cast Iron Housing 540 rpm PTO Driven Gearbox 1:1.47 Cast Iron Housing Tailwheel 4” x 8” x 15” Laminated Tire, cast iron hub Optional - 4” x 16” Solid Rubber Tire 12/28/05 RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters 312-556M 21 Table of Contents Section 6: Features and Benefits RCR15 Series Single Deck Rotary Cutters Features Benefits Tractor HP range 15- 50hp Cutting widths 42” and 48” Floating top link Permits deck to follow the terrain for an even cut. Two hole position to allow greater lift leverage for smaller tractors. Clevis Hitch Cat I, 3-point hitch with floating link for easy hook-up. Fully welded deck Robotic welded. Adds additional strength. Round back design Helps discharge grass better than enclosed or partially enclosed cutters. High blade tip speed Ensures clean cut. 42” = 11,459 fpm 48” = 13,090 fpm Rubber guards (front and rear) Protect against flying debris. Full length skid shoes Provides sidewall reinforcement and full protection to bottom of sidewall. Cat. 3 driveline with shear-bolt Shear bolt offers maximum driveline protection. Cat. 3 driveline with 2-plate slip-clutch Slip-clutch driveline offers convenience for continual work. Laminated tailwheel Laminated material is long lasting in rough conditions. Solid rubber tailwheel Can’t go flat. Heavy-duty spindle on tailwheel Tailwheels take a beating, 1 1/4” spindle gives the strength to protect tailwheel assembly. Cutting Height 1” - 9” cutting height for wide range of cutting conditions. 10 Gauge stump jumper Allows cutter to slide over obstructions protecting the gearbox output shaft. Splined bladebar hub Allows for tight positive fit of stump jumper and blade bar to gearbox output shaft. Surpassed rugged industry standards All Land Pride Cutters have been designed and tested and meet rigorous volunt...

Herunterladen

Geben Sie zwei Ziffern: