Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: McCulloch Dateigröße: 1.76 mb Dateiname: Unterrichtssprache:

NOTE: For proper operation, always refer to the instructions accompanying the trimmer head being used. Trimmer head styles: Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head on the ground during operation. Manual. The operator indexes line manually with the grass trimmer stopped. Fixed. The operator must stop the unit and add new lengths of trimmer line manually. Flail. This device, designed for clearing weeds and light brush, features three nylon blades attached to the head by pivots. NOTE: Additional hardware may be required to mount the Fixed Line or the Flail type trimmer heads. Edging Tilt the handle about 100° to the left (from horizontal) and move forward, holding the trimmer or brushcutter vertically as shown. Engine Operating Speeds Operate at full throttle while cutting grass. CAUTION! Operation at low rpm can lead to premature clutch failure. Trimming and Mowing Grass Hold the grass trimmer so the trimmer head is angled slightly into the area to be cut. To ensure maximum trimmer-line service life, cut only with the tip of the trimmer line. Cut grass by swinging the unit's trimmer head from left to right. Keep the trimmer head horizontal. CAUTION! Do not push the rotating line into trees, wire fences or any material that could tangle or break line ends. CAUTION! ...................................................................... recommended by the manufacturer. Never use, for example, wire or wire- rope, which can break off and become a dangerous projectile. Cut from left to right Cut Return WARNING! Remove all objects such as rocks, broken glass, nails, wire, or string, which can be thrown or become entangled in the cutting attachment. CAUTION! Y Operation of trimmer without a cutting attachment shield and using excessive line length can lead to premature clutch failure. Y Operation at low rpm can lead to premature clutch failure. Tilt the handle about 100° to the left Operation (continued) Using a blade Y Whenever you strike a hard object WARNING! with a blade, always stop the brushcutter and carefully inspect the Y Before working with a blade-equipped blade for damage. NEVER OPER- unit, always inspect and clean the ATE THE BRUSHCUTTER WITH A area of objects that could interfere DAMAGED BLADE! with or damage the blade. Y A blade-equipped unit must be Y Never use a blade near sidewalks, equipped with a bicycle-type handle- fence posts, buildings or other objects bar or barrier bar as well as a har that could cause injury or damage. ness or shoulder strap.Y Never use a blade for purposes other Y Always make sure the cutting attach- than those for which it was designed. ment shield is properly installed before operating this unit. Blade Thrust “Blade thrust” is a sudden sideways or backward motion of the brushcutter. Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CONSTANTLY ALERT FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS! WARNING! Blade thrust can occur without warning if the blade snags, stalls or binds. Using a blade The blade rotates counter-clockwise. For best performance and to minimize being stuck by debris, move the blade from right to left while advancing on your work. Position the blade so cuts are made between the blade’s 8 o’clock and 10 o’clock positions (as viewed from above). DO NOT cut between the 10 o’clock and 5 o’clock positions. WARNING! When cutting wood with a blade, feed the blade slowly—never strike or “slam” a spinning blade against the wood. WARNING! DO NOT use 2-tooth or non- Shindaiwa approved 4-tooth cutting blades with Shindaiwa trimmers and brushcutters. WARNING! Blade thrust is more likely to .............................................................................. see the material being cut. Brushcutter Handlebar A brushcutter handlebar or barrier bar helps prevent the operator from moving forward, or the unit moving rearward, thus preventing inadvertent bodily contact with the blade. ALWAYS KEEP THE HANDLEBAR OR BARRIER BAR SECURELY IN PLACE ON THE UNIT! Brushcutter Shoulder Strap A shoulder strap provides additional protection against blade thrust. In addition, a shoulder strap gives significant support and comfort to help ensure safe and efficient operation. When operating a unit with a blade, make sure both the handle and shoulder strap are adjusted to the size of the operator using the unit. Engine Operating Speeds Operate the unit at full throttle while cutting. Best fuel efficiency is obtained by releasing the throttle when swinging back after a cut. Y To prevent possible engine damage, do not allow the brushcutter to run at high speeds without a load. Y Avoid operating the engine at low speeds. Doing so can lead to rapid clutch wear. In addition, slow-speed operation tends to cause grass and debris to wrap around the cutting head. DONOT CUT Vertical Cuts Hold the brushcutter with the blade at a 90° angle to the ground so the blade’s bottom edge rotates towar...

Herunterladen

Geben Sie zwei Ziffern: