Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Makita Dateigröße: 2.56 mb Dateiname: RBC253.pdf Unterrichtssprache:

11) 1. Install the clamp on the drive shaft so that t h e projection of the clamp is inserted into the opening between the gear case and the drive shaft. 2. Attach the protector with two installation bolts M6x20. Mounting the cutter blade (Fig. 12,13) 1. Turn the machine upside down so that you can easily install the cutter blade. Insert the hex wrench through the hole in the back of the gear case and turn the tightening washer until it is locked with the hex wrench (or the shaft is locked). 2. 3. Using the socket wrench, remove the left-handed nut (by turning it clockwise). Also remove the tightening washer. 4. Mount the cutter blade onto the shaft so that the guide of the support washer fits in t h e arbor hole in the cutter blade. Install the tightening washer and secure the cutter blade with the nut. (Tightening torque: 130-230 Kg-cm,l 15-200 in- Ibs). NOTE: Always wear gloves when handling t h e cutter blade. WARNING: The cutter blade s h o u l d be installed firmly a n d securely. (Fig. 14) If t h e guide of t h e s u p p o r t w a s h e r d o e s n ' t fit in t h e arbor hole in t h e cutter blade. t h e b r u s h cutter will make violent vibration. It not only s h o r t e n s t h e machine life, b u t may also allow the cutter blade t o loosen a n d fly off. Failure to install the blade correctly can c a u s e s e r i o u s injury. 7 . !FA PO RTANT! READ THE INSTRUCTIONFSO R USE O F THE B R U S H C U T T E R BLADE (PAGE 15) BEFOFIE O F E R A T I N G T H I S MACHINE. Gear case Installation bolt M6x20 Protector Fig. 11 ~ r-- I HE PREPARING FOR OPERATION Fuel and oil mixture This product is powered by a two-cycle engine and requires pre-mixing gasoline and two-cycle engine 011 Inspect the fuel tank and f i l l with clean, fresh fuel and oil of the proper rrtxture to assure the longer life of the tool Use the following mixed gas Gasoline Genuine Makita Two-cycle engine oil = 50 1 or Gasoline Other manufacturer's Two-cycle engine oil = 25 1 recommended ~ ____ -. ____- - __ - - . FOR CALIFORNIA REGULATION: THIS EQUIPMENT IS CERTIFIED TO OPERATE ON GASOLINE + TWO-CYCLE ENGINE OIL WHEN MIXING GASOLINE WITH TWO-CYCLE ENGINE OIL,USE ONLY GASOLINE WHICH CONTAINS NO ETHANOL OR METHANOL (TYPES OF ALCOHOL). THIS WILL HELP TO AVOID POSSIBLE DAMAGE TO ENGINE FUEL LINES AND OTHER ENGINE PARTS. DO NOT MIX GASOLINE AND OIL DIRECTLY IN THE FUEL TANK. IMPORTANT: Failure to follow groper fuel mix instructions may cause damage to t h e engine. CAUTION: 1 . When preparing fuel mixture, mix only the amount needed for the job you are to do. Do not use fuel mixture that has been stored longer than tbvo months. Fuel mixture stored longer than this will cause hard starting and poor performance, If fuel mix has been stored longer than this time, it should be removed and replaced with a fresh mixture. 2. Never- f i l l the fuel tank to the very top 3. Never add fuel to the tank in a closed, unventilated area. 4 Do no: add fuel to this unit close to an open fire or sparks 5. Be sure to wipe off spilled fuel before attempting to start the engine 6. Do not attempt to refuel a hot engine. Check points before operation 1 . Check for loose bolts, nuts and fittings. 2. Check the air cleaner for dirt. Clean t h e air filter of all dirt, etc. before operation 3. Check to be sure that protector is securely in place. REFUELING Use Oil-gasoline mixture for fuel as noted in "Fuel and Oil Mixture" on previous page Always s h u t off the engine and allow it to cool before refueling. Thoroughly clean the area around the fuel filter cap, to prevent dirt from getting into the fuel tank. Unscrew the fuel cap and f i l l the tank with fuel, then screw on the fuel filler cap tightly(EdT. /'3,'.. Wipe off any spilled fuel before starting. and check for leakage - I Check for fuel leakage while refueling and during operation If fuel or oil leakage is found, do not start or run the engine until the leak is fixed and any spilled fuel has been wiped away. Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always wear protective gloves during refueling. Change and clean protective clothing at regular intervals. Take care not to spill either fuel oi oil in order to prevent soil contamination (environmental protection) Clean the brush cutter or string trimmer immediately after fuel has been spilt Avoid any fuel contact with your clothing. Change your clothing instantly if fuel has been spilt on it (a danger to life) Inspect the fuel cap at regular intervals making sure that it I S securely tightened. Select bare ground for fueling and move at least 10 feet (3m) from fueling spot before starting the engine(Fy, &), Never refuel in closed rooms. Fuel vapors accumulate at ground level (risk of explosions). Only transport and store fuel in a container approved for gasoline. Make sure the stored fuel is not accessible to children. WARNING! Gasoline is extremely flammable fuel Use extreme caution when handling gasoline or fuel mix. Do not smoke ...

Herunterladen

Geben Sie zwei Ziffern: