Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
40” NOTE: When adjusting tines, be sure the cutting edges enter the soil first. MAINTENANCE AND LUBRICATION ENGINE - Service engine in accordance with the engine manufacturer’s owner’s guide. NOTE: To drain oil, remove oil filler plug and tip tiller on its side. Drain oil while the engine is warm. See engine manual for filling instructions. GEAR CASE - Proper lubricant level should be up to the front pipe plug. Check with tiller on a level surface. Add lubricant through the vented pipe plug hole. Add enough to bring level up to front plug hole. Use Molilube SAE 140 Gear Oil or equivalent. Gear case should be maintained with five (5) ounces of lubricant. Lubricate the upper bushing in the gear case with a small amount of grease. Do not over lubricate as any excess will enter the gear case proper. Use a high pressure gun grease. THROTTLE - Periodically lubricate throttle control lever and throttle control wire assembly with a few drops of light oil (SAE 10 or 20) for ease of operation. FORM NO. 770-912E ! I BELTS - “V” Belts and pulley assemblies are accessible at the rear of the tiller. The belts are changed as described below. To remove large belt — 1. Place clutch control handle in “Neutral” position. 2. Remove lower belt guard (13). 3. Loosen (Do not remove) belt clip (16) and remove belt (56). To remove small belt — 1. Remove large belt as described. 2. Place clutch control handle in “Forward” position. 3. Loosen belt retainer (10) and remove belt (57). To replace small belt — 1. Position belt on pulleys.„Be sure belt is in proper pulley grooves. 2. Move clutch control handle to “Neutral” position. 3. Move belt retainer (10) into position against reverse pivot bracket and tighten. Do not tighten excessively. Pulley (71) should have approximately 1/16” end play. To replace large belt — 1. Position belt on pulley (35). 2. Position belt on pulley (68). 3. Position belt on pulley (73). 4. Replace and.tighten lower guard (13). 5. Place clutch control handle in “Forward” position. 6. Tighten belt clip (16). CAUTION: Upper part of belt clip should clear belt by 1/8”. SERVICE DRIVE BELT SLIPS 1. Lubricate contact surface between pivot bracket assembly and adjustment plate. 2. Check pivot bracket assembly locknuts for excessive tightness. 3. Check control rod for improper assembly. If adjustment tube is attached to lower end instead of upper end, it may bind on control lever and prevent full use of tension spring. 4. If spring tension is still insufficient, adjust to another mounting hole on control lever. 5. Some measure of belt adjustment may be made by loosening the mounting bolts on the adjustment plate and moving as needed. This adjustment is usually used for reverse drive wheel adjustments. 6. Large pulley and belt may be rubbing on lower belt guard. 7. Idler pulley must operate freely. 8. Belt guard or clips must not touch the belt when it is tightened. GENERAL - Check periodically all nuts and bolts, loose nuts and bolts can cause permanent damage to your unit. Keep all nuts and bolts securely tightened. STORAGE - The following steps should be taken to prepare your tiller for storage. 1. Clean tiller thoroughly and lubricate as described in the preceding instructions. 2. Coat tilling tines with grease to prevent rusting. 3. Prepare engine for storage in accordance with engine manufacturer’s owner’s guide. 4. Block tiller legs to raise tires clear of floor. Be sure tiller is level. 5. Store in a dry clean area. ATTACHMENTS EXTENSION TINES - This attachment is available to increase your tilling width up to 40”. Extension tines are easily installed and removed. Order under part number 297-164. FURROW OPENER - This attachment is easily installed on the depth bar of your tiller. It can be used for either furrowing or hilling operations. These attachments are available through your local dealer. For wide (2” x .43” depth bar, order furrow opener 297-179. For narrow (1-1/2” x 3/8”) depth bar, order furrow opener 297-178. NOTES REVERSE DRIVE WHEEL ADJUSTMENT 1. Reverse drive wheel should line up with its matching pulley. If it does not, loosen pulley to which reversing drive wheel is attached and align as needed. When reassembling, tighten set screw securely. 2. Matching pulley for reversing drive wheel can be mounted one way only. The reversing drive wheel must operate in the deeper groove. 3. If belt retainer touches engine pulley after adjustment, move to outside mounting or bend away as needed. 4. Additional reverse adjustment may be made by loosening the mounting bolts on the adjustment plate and moving as needed. 5. Reverse should operate only when control handle assembly is held in reverse position. Adjust control rod for proper operating position. NOTE: If belts are excessively stretched, replacement will be necessary. FORM NO. 770-9 12F TILLER DRIVE MECHANISM ALLEM CAP SCREW 710-185 TWO STAGE REVERSE PULLEY 7CJL110 REVERSE DRIVE WHEEL 717-...