Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
IO.Stop operation immediately if you notice anything abnormal. 11. Always switch off and wait for blades to come to a complete stop before adjusting any parts, cleaning out chips or approaching the blade. 12. Never stick your finger into the chip chute. Chute may jam when cutting damp wood. Turn off the planer-jointer and then clean out chips with a stick. 13. Do not touch blades right after operation, they may be extremely hot and could burn your skin. 14. Don't abuse cord. Never yank cord to disconnect from receptacle. Keep cord from heat, oil and sharp edges. 15. Do not use auto-planer and jointer at the same time. Overloading of the motor can occur. FOR JOINTER 1. Maintain the proper relationships of infeed and outfeed table surfaces and cutterhead blade path. 2. Do not perform jointing operations on material shorter than 140 mm (5-1/2 inches), narrower than 19mm (3/4 inch), or less than 12.7 mm (112 inch) thick. 3.Do not perform planing operations on material shorter than 140 mm (5-1/2 inches), narrower than 19 mm (3/4 inch), wider than 155 mm (6-1/8inches) or thinner than 12.7 mm (112 inch). 4. Support the workpiece adequately at all times during operation; maintain control of the work at all times. 5. Do not back the work toward the infeed table. 6. Do not attempt to perform an abnormal or little-used operation without study and the use of adequate hold-down/push blocks, jigs, fixtures, stops and the like. FOR AUTO-PLANER 1. Two or more pieces of narrow but similar thickness stock can be passed through the auto-planer side by side. However, allow some spacing between the stock to permit the feed rollers to grip the thinnest piece. Otherwise, a slightly thinner piece could be kicked back by the cutterhead. 2. Determine the depth of cut according to the table shown on the front of the tool. Do not attempt to cut more than the specified amount in one pass. WARNING For Your Own Safety, Read Instruction Manual Before Operating Jointer 1. Wear eye protection. 2. Never perform jointing or planing operation with cutter head or drive guard removed. 3.Never make jointing or planing cut deeper than 3 mm (118 inch). 4. Always use hold-down/push blocks for jointing material narrower than 76.2 mm (3inches), or planing material thinner than 76.2 mm (3inches). SAVE THESE INSTRUCTIONS. Movement and transport of planer-jointer When moving the tool, hold it as shown in the figure. When transporting it by vehicle, secure with a rope or other substantial means to prevent tipping or movement. Positioning the planer-jointer Locate the tool in a well lit and level place where you can maintain good footing and balance. Bolt it to the workbench using the bolt holes provided in the base. When locating it without bolting, use the stays provided to help maintain its stability. Remove the two bolts which secure the stays. Extend the stays by one bolt hole and secure them using the bolts. Installing the crank handle Install the crank handle using the socket wrench provided. Switch action CAUTION : Before plugging in the tool, always be sure that the tool is switched off. To start the tool, insert the key and press the ON side of the switch. To stop it, press the OFF side. CAUTION : When not using the tool, remove the key and store it in a secure place. This prevents unauthorized operation. AUTO-PLANER FUNCTIONS: Dimensional adjustment I Scale-\ Raise the table by turning the crank handle clockwise until the indicator plate points to the scale graduation indicating the de- sired finished dimension. One full turn of the crank handle moves the table 2 mm (3/32") up or down. The scale has inch graduations on its right side and metric graduations on its left side. I Crank h Adjusting the depth of cut The maximum depth of cut differs depend- ing upon the width of workpiece being cut. 3 mm (1 18") Refer to the table at right. When you wish to cut deeper than the amount specified in s the table, make two or more passes to d avoid overloading the motor, jamming the workpiece and subsequent damage. 1 (1132"l " To adjust the depth of cut, proceed as follows. Insert the workpiece flat on the infeed table top. Raise the table by turning the crank handle clockwise. The depth gauge Indicator plate andled Max demh of cut nm 150" 132"l 16 I Width will rise and the amount of gauge rise indi- Scale 7 cates the depth of cut. &\' Indicator plate CAUTION : Always raise the table when aligning the indicator plate with the graduation indicating the desired finished dimension. If the table is lowered into the desired finished dimen- sion, additional play in the screw may result. This may cause an undesired finished dimension, gouging or sniping of the workpiece. *Always place the workpiece flat on the infeed table top when predetermining the depth of cut. Otherwise, the predetermined depth of cut will differ from actual depth of cut. Operation Determine the depth of cut as described before. Insert the workpiece flat on the table top. When cutting a long o...