Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Harbor Freight Tools
Dateigröße: 145.82 kb
Dateiname: 6d448eb6-b855-40df-8ef1-bc61d8ac70f9.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 8. Do not overreach. Keep proper footing and balance at all times. SKU 90310 Page 2 9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. The handle must be kept clean, dry, and free from oil and grease at all times. 10. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired. 11. Take caution as some woods contain preservatives such as copper chromium arsenate (CCA) which can be toxic. When cutting these materials extra care should be taken to avoid inhalation and minimize skin contact. 12. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 13. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 14. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 15. Maintenance. During periods of storage, coat the bare metal surfaces with light oil to inhibit rust. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the parts shown on page 5 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Warning! Do not let the blades come in contact with your hands while planing or changing the blades. They are extremely sharp and will cause severe injury if contacted. SKU 90310 Page 3 Operation Refer to the Assembly Drawing on page 5 and FIGURE 1 below. Note: The front blade (fillister) is stationary and the rear blade is movable and replaceable. 1. To change or replace Blades, turn the Blade Removal Knob (see below) counterclockwise and lift off the blade holder (see below). Set the Blade in so that it fits over the set screw and is properly aligned. Replace the Blade Holder and tighten the Blade Removal Knob. 2. Adjust the amount of blade you want to contact the workpiece by pressing the Blade Adjustment lever side to side (see Assembly Drawing on page 5). FIGURE 1 Blade Removal Knob Blade Holder Blade Set Screw 3. There are two fences. To adjust the Depth Gauge Fence, loosen the Lock Screw and move the Fence up or down to determine the depth you cut into the wood (see Assembly Drawing on page 5). To assemble the Fence located on the left side of the tool, first thread on the Steel Rod into the left side of tool’s housing. The Fence slides over the end of the Steel Rod and is locked in place by the Fence Adjustment knob. To adjust this Fence (determines width of cutting area), loosen the Fence Adjuster knob and move the Fence either closer or further from the body of the Planer. With the Fence in the desired position, secure it in place by tightening the Fence Adjuster knob. 4. Make sure the workpiece is securely fastened down. Note: If you are using the front blade for bullnosing (See Assembly Drawing on page 5), make sure the rear blade is adjusted up so it doesn’t contact the workpiece. 5. Do not force the Plane or press down on it. Move it forward, taking off a little wood at a time. If the Plane does not move forward easily, retract the Blade more as explained in step 2 above. SKU 90310 Page 4 Assembly Drawing Handle Blade Adjustment Lever #8 Blade #1 Blade Removal Knob #7 Fence #4 Fence Adjustment Lock Screw #6 Steel Rod #3 Lock Screw #5 Note: This Plane includes two blades and two fences. Depth Gauge Fence #2 Front Blade REPLACEMENT PARTS #1 Blade #2 Depth Gauge Fence #3 Steel Rod #4 Fence #5 Lock Screw #6 Fence Adjustment Lock Screw #7 Blade Removal Knob #8 Blade Adjustment Lever Mainten...