Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
9 10 11 12 13 14 15 16 17 18 19 20 23 22 1 2 3 4 5 7 8 1. Open the battery cover. 2. Place the 2 (AAA) batteries (included) into the compartment. Be sure the positive and negative terminals are positioned correctly as shown. 3. Close the battery cover. 2 - (AAA) Batteries User Guide Remote control Connecting the antenna 1. With the antenna in the down position, screw it into the RF IN antenna jack on the TV. 2. For the best reception, stretch the antenna out to its fullest length before scanning for channels. Charging This television contains a built-in rechargeable battery. You may power the television by charging its internal battery or you may power the television by using the included AC adaptor. Follow the instructions below to charge the television properly. 1. Connect the AC adaptor to the DC 9-12V IN jack on the TV and plug it into a wall receptacle. 2. Charging time depends on whether the TV is ON during charging or in standby mode. If the TV is ON – the charge time is approximately 6 hours. If the TV is in standby mode – the charge time is approximately 4 hours. 3. When battery strength is low, the TV will display the following icon on the screen: ,this means it is time to recharge the battery. 4. The [Standby/Power] indicator light on the front of the TV turns green when: The power cord is connected, and the TV is fully charged. The TV is running on battery power. The first time the television is turned on you must scan for available channels. You should also scan for available channels whenever you are in a new area, or when reception is bad. 1. Make sure that the antenna is connected to the TV and slide the power [ON/OFF] switch to the ON position. 2. When you turn on the TV for the first time, the following screen will be displayed: 3. If this screen does not appear, then press the [AUTO/OK] button on the TV. 4. Press the [VOL+] button to select “Yes” and press [AUTO/OK] button to confirm. 5. The TV will start scanning for available channels and store them into memory. Scanning by remote control 1. Press the [MENU] button on the remote and press the [ ] button to select: 2. Press the [ ] button to select “Antenna”. 3. Press the [ ] button to select “Air” or “CATV” (cable TV), depending on the type of connection. 4. Press the [ ] button to scroll to “Auto Scan” and press the [ ] button twice. The TV will start scanning for available channels and store them into memory. Note: Do not move or unplug the TV while scanning for channels/subchannels. 2 1 Getting started Scanning for channels Note: The antenna must be connected to receive the highest amount of channels available during channel scanning. Note: Use the included car charger to charge the TV in a car or boat. This television is not meant to be used in a moving vehicle. ATSC Digital tuners are not capable of receiving a signal when in motion. Do not move or unplug the TV while scanning for channels/programs as this will interrupt the scanning process and you will not receive all possible channels/subchannels. Select 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. LCD screen Dual speakers [Standby/Power] indicator [MENU] button [CH-] button [CH+] button [AUTO/OK] button [VOL-] button [VOL+] button [MODE] button Remote sensor RF IN antenna jack VIDEO IN jack AUDIO IN L jack AUDIO IN R jack Headphone jack Power [ON/OFF] switch DC 9-12V IN jack TV stand (pull) Battery compartment 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. [MUTE] button [PICTURE] button [MENU] button [SLEEP] button [ ] left button Numeric buttons [ ] previous channel button [VOL-] volume down button [POWER] button [MTS] sound field button [ZOOM] display mode button [EXIT] button [EPG] program guide button [ ] up button [ ] right button [ENTER] button [ ] down button [TV/AV] source button [INFO] program information button [CH+] channel up button [CH-] channel down button [ ----] channel program button [VOL+] volume up button PTV-701 Portable Digital TelevisionPortable Digital Television 7.0” LCD Display Cover Remote control Batteries DC Car Charger AC Adaptor A / V Cables 12 13 14 16 15 18 17 1920 3 1 2 4 5 6 7 8 9 10 11 User Guide Digital TV Remote Control Antenna Location of controlsIncluded Installing the batteries Polaroid and Polaroid & Pixel are trademarks of PLR IP Holdings, LLC, used under license. PLR IP Holdings, LLC does not manufacture this product or provide any Manufacturer’s Warranty or support. 9 10 11 12 13 14 15 16 17 18 19 20 23 22 1 2 3 4 5 7 8 1. Open the battery cover. 2. Place the 2 (AAA) batteries (included) into the compartment. Be sure the positive and negative terminals are positioned correctly as shown. 3. Close the battery cover. 2 - (AAA) Batteries User Guide Remote control Connecting the antenna 1. With the antenna in the down position, screw it into the RF IN antenna jack on the TV. 2. For the best reception, stretch the antenna out to its fullest lengt...