Stimmen - 0, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 1.21 mb Dateiname: Unterrichtssprache:

3 Press and hold the DIMMER key for more than 2 seconds to select the A-REC or M-REC mode. • The mode changes every 2 seconds as shown below. 1 Rec mode off : The digital input record mode is switched off. 2 A-REC : The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for recording. 3 M-REC : The input signal type at the moment this mode is selected is held throughout this mode. For A-REC mode: For M-REC mode: 4 Start playback, then start recording. • If the audio reproduction stops in the middle due to change in the input signals, etc., press the DIMMER key. 19 EN Listening to radio broadcasts The receiver can store up to 40 stations in the memory and recall them by one-touch operation. Tuning radio stations MULTI CONTROL INPUT SELECTORBAND AUTO Joystick (MULTI CONTROL 5/.) TUNING1/ . BAND TUNER AUTO 1Use the INPUT SELECTOR knob or TUNER key to select the tuner. 2Use the BAND key to select the desired broadcast band. “AM” or “FM” indicator Each press switches the band appears in the display as follows: 1 FM 2 AM 3Use the AUTO key to select the desired tuning method. Each press switches the tuning method as follows: 1 AUTO lit (auto tuning) 2 AUTO not lit (manual tuning) “AUTO” indicator lights up in the display. • Normally, set to “AUTO” (auto tuning). If the radio waves are weak and there is a lot of interference, switch to manual tuning. (With manual tuning, stereo broadcasts will be received in monaural.) 4Use the MULTI CONTROL knob or Joystick, or TUNING 1 / .keys to select the station. “ST.” lights when Frequency a broadcast is being display received in stereo. “TUNED” is displayed when a station is received. Presetting radio stations manually MEMORY MULTI CONTROL 1Tune to the station you want to store. 2Press the MEMORY key while receiving the station. Blinks for 5 seconds Lights for 5 seconds Proceed to step 3 within 5 seconds. (If more than 5 seconds elapse, press the MEMORY key again). 3Use the MULTI CONTROL knob to select one of the station presets (1 – 40). 4Press the MEMORY key again to confirm the setting. • Repeat steps 1, 2, 3, and 4 to store as many stations as necessary. • If you store a station at a previously used preset, the previous station will be replaced by the new one. Auto tuning : The next station is tuned automatically. Manual tuning : Turn the knob (press the key) to select the desired station. 20 EN Listening to radio broadcasts Listening to radio broadcasts Numeric keys TUNER 1Press the TUNER key to select tuner as the source. 2Enter the number of the preset station you want to receive (up to “40”). Press the numeric keys in the following order: For “15”, press ................................ 0,5 For “20”, press ................................ 0,0,) • If you make a mistake entering a two digit number, press the +10 key repeatedly to return to the original display and start again. Receiving preset stations in order (P.CALL) Joystick (P.CALL 4 / .) TUNER 1Press the TUNER key to select tuner as the source. 2Use the Joystick to adjust the P.CALL 4..direction to select the desired station. • Each time you push the Joystick, another preset station is received in order. Pushing the Joystick to P.CALL . does the following : Pushing the Joystick to P.CALL 4 does the following : Holding the Joystick on . or 4 direction, lets you skip through the presets, receiving each preset station at 0.5 second intervals. 21 EN Ambience effects This receiver is equipped with listening modes that allow you to enjoy an enhanced sonic ambience with a variety of video sources. In order to obtain the optimum effect from the surround modes, make sure to input the proper speaker settings beforehand. % Surround modes DTS The DTS multi-channel audio format is available on CD, LD and DVD software. DTS is a strictly digital format and cannot be decoded inside most CD, LD or DVD players. For this reason, if you attempt to listen to DTS encoded software through the analog output of your new CD, LD or DVD player, you will experience digital noise in most cases. This noise can be quite loud if the analog output is connected directly to a high power amplification system. Proper measures for playing the digital output as described below should be taken to avoid this situation. To enjoy DTS Digital Surround playback, an external 5.1 channel DTS Digital Surround decoder system or an amplifier with a built-in DTS Digital Surround decoder must be connected to the digital output (S/P DIF, AES/EBU or TosLink) of a CD, LD or DVD player. All models are incorporated with the DTS decoder. * LFE = Low Frequency Effects. This channel delivers separate non- directional bass signals to the subwoofer for more dynamic deep bass sound effects. DTS has a .1 or LFE channel. The indication “LFE” appears in the display when a signal is being input for this channel. *Optional in this mode. Center speaker Front speaker (L, R) Surround speaker (L, R) Subwoofe...

Herunterladen

Geben Sie zwei Ziffern: