Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 760.77 kb Dateiname: Unterrichtssprache:

Digital to Digital Recording: The PCM digital signal input through any DIGITAL IN jack is output digitally at the digital jack. For more information on this connection, see “Connecting Your MD Recorder or Primary Tape Deck” on pageE20 of the Connections and Setup Guide. Dolby Digital and DTS signals cannot be recorded. Digital to Analog Recording: While home VCRs can record only two channels of audio, the receiver is capable of "down-mixing" the multi-channel audio of Dolby Digital, DTS or MPEG into stereo sound. Down-mixing is available by setting the Digital Rec mode to “REC MODE: AUTO or “REC MODE: MANUAL”. To set the Digital Rec mode: 1. Press the F. SHIFT =REC (REC MODE)* key on Remote Control unit. 2. Select “REC MODE: AUTO or “REC MODE :MANUAL”. When a source recorded by down-mixing a multi-channel source is played back in the Dolby Pro Logic mode, the audio can be reproduced in 4channel surround sound. Using Using Receiver How Do I Adjust the LCD Display? How Do I Adjust the LCD Display? Using Remote Control unit under low light When using Remote Control unit under low light, the back light of the 1 2 34 5 67 8 910 11 12+10 0+100/8 /71 1 LCD display can be turned on. • Press and hold the F.SHIFT key for more than 2 seconds. The back light is turned on and off every 2 seconds of holding. If the is blinked, the back light cannot be turned on because the batteries are nearly exhausted. Adjusting the contrast of LCD display The contrast of the LCD display can be adjusted to improve the visibility. 1. Press the Music key or Movie key to display “Menu”. 2. Press the Menu (LCD function key 2) key. 3. Press the Setup (LCD function key 2) key. 4. Press the LCD cursor up/down ( / ) key to select “03. Contrast”, then press the Enter key. 5. Select the desired contrast with the LCD cursor up/down ( / ) key. The previous menu re-appears in about 3 seconds after the above operation. How Do I Adjust the LCD Display? Adjusting the brightness of receiver When the ambient light is low, for example in the night, the brightness of the receiver’s display can be dimmed and LED indicators (DTS, 96k fs, HDCD, DOLBY DIGITAL, MPEG and D.R.I.V.E. only) can be disabled. • Press the F.SHIFT = LISTEN M. (DIMMER)* keys. Each press of the LISTEN M. key switches the brightness as shown below. 1 Display/bright Indicators/enabled 2 Display/dim Indicators/enabled 3 Display/dim Indicators/disabled Selecting the display mode of receiver front panel • Press and hold the LISTEN MODE key on the receiver for more than 2 seconds. The displayed information is switched every 2 seconds of holding the key. A: Connected Device Input Type DVD AUTO B: Input Terminal Connected Device VIDEO3 : DVD C: Listen Mode DOLBY DIGITAL "Input Type" is displayed only when a selector with digital input is se lected. When the input mode is PHONO, TUNER or AV AUX, the connected device and listen mode are displayed alternately. * When an operation is described as [F.SHIFT = LISTEN M. (DIMMER) key], for example, press the F.SHIFT key and press the next key (the LISTEN M. (DIMMER) key in this case) within 8 seconds. Using Using Receiver Executing Several Operations at Once (Macro function) Executing Several Operations at Once (Macro function) By registering several steps of remote control operations beforehand, these operations can be executed with a single operation. This function is referred to as the macro function. The receiver can register up to three sets of macros. Up to 20 operation steps can be recorded for one macro. Registering a macro 1. Press and hold the MACRO key on Remote Control unit for more than 2 seconds. 2. Within 8 seconds, press the MUSIC (MACRO1), MOVIE (MACRO2) or TV (MACRO3) key. 3. Press the control keys in the order you want to execute them. 4. Press the MACRO key. Now the registration is complete. 5. Check the macro according to the following “Executing a macro” 2WAY LCD REMOTE CONTROL UNIT procedure. When there is a function which does not perform interim operation, a delay must be inserted. To insert a delay, insert a macro step for a key not related to the operation at that time (for example the STOP key during stop) etc. befor the function for which the operation is to be delayed. Press each key slowly and firmly. “Full” is displayed when the maximum number of steps have been registered. If you do not perform any operation for more than 8 seconds in the middle of registration, the registration mode is canceled and the previous registration remains without being cleared. Executing Several Operations at Once (Macro function) Example of registration: In the following example, the steps for turning the TV on, turning the VCR on, setting the TV channel and playing the VCR will be registered in Macro 2. 1. Press and hold the MACRO key on Remote Control unit for more than 2 seconds. 2. Within 8 seconds, press the MOVIE (MACRO2) key. 3. Perform registration. 1. Press the TV key. 2. Press the AV POWER key. 3. Press numeric key 2 (channel setti...

Herunterladen

Geben Sie zwei Ziffern: