Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Actual displays depend on the changes you make. If you change one setting, the other corresponding setting will also change. ©Turn [INPUT SELECTOR] to change the setting. When you turn the selector: COAX — OPT1 — OPT2 t_I © Repeat © and © to change other D-INPUT settings. DIMMER Turn [INPUT SELECTOR] to change the setting. When you turn the selector: OFF — ON RQT5982 Preparations SPEAKERS A, B Customizing your receiver For front speakers with an impedance under 6 Q Turn “LOW IMP" on if even one of your speakers has an impedance under 6 ft. Press and hold [A] or [B] until “LOW IMP” lights up on the display. Press and hold down again to cancel “LOW IMP". Note that when “LOW IMP” is on, SPEAKERS A and B cannot be used at the same time. 14 RQT5982 Adjusting speaker output level ; Adjust the level of the speakers so they are the same apparent level_ as the front speakers when you are sitting where you would normally enjoy a source. 1 Press [A] or [BI-WIRE] to turn on SPEAKERS A or BI-WIRE. You cannot adjust output level when SPEAKERS B is on. 2 Press [TEST] to output the test signal. DSP sound mode switches to SURROUND mode. The signal is output from each speaker in order for about two seconds each: - L: Front speaker (left) C: Center speaker R: Front speaker (right) RS: Surround speaker (right) LS: Surround speaker (left) SW: Subwoofer Speakers set as “NONE" or “NO” are skipped. The test signal will not be output if the VGCA (■> page 20) or DVD 6CH INPUT is on (^ page 19). 3 Adjust the volume to the level normally used. Adjust the balance of the front speakers if necessary H page 21). 4 Press [LEVEL] to select the speaker channel to adjust. The current level appears on the display. Press again to change the speaker channel. Speakers set as “NONE” or “NO” are skipped. 5 Press [+] or [-] to adjust the level to the same apparent level as the front speakers. . C, RS, and LS can be adjusted between -10 dB and +10 dB, with zero being the current level of the front speakers. SW can be set to MIN, between 1 to 19, or MAX. Repeat steps 4 and 5 for each speaker channel. 6 Press [TEST] to stop the test signal. For your reference Subwoofer output is easily influenced by the source played. You can achieve better results by adjusting its output while listening to a source (^ page 21). DSP SOUND MODE DIGITAL INPUT Q /_ / /_ /_/ /_ / / / I I / I / / / — PROGRAM FORMAT — ю m -=SOUND MODE-ÍSTEREO) DSP sound modes The digital sound processor (DSP) in this unit can decode Dolby Digital and DTS digital signals. It automatically determines the type of signal, PCM, Dolby Digital, or DTS, and processes it accordingly. The DSP can add surround-like effects to stereo sources (analog or PCM signals). Choose from the STEREO, SURROUND, or SFC modes. « PCM with a sampling frequency of 44.1 kHz is the digital signal format normally found on CDs. Some DVDs also use this format but often with a higher sampling rate. • This unit cannot process other digital signal formats, such as PCM signals with a sampling frequency of 192 kHz and MPEG. SiliE R EOjmode Use this mode to play digital or analog stereo sources or to play surround sources through two speakers. When surround sources are played in this mode, the sounds intended for the other speaker channels are played through the front speakers. Select this mode when you are playing a digital surround source (Dolby Digital or DTS) or an analog source that is recorded with Dolby Surround (VCR, for example). — PROGRAM FORMAT — О > I О О l~ > Í t\ ! Tí r¡—II С inn м /_/ ' w ±i rm ilfei r~Rs~~] -SOUND MODE- □□DIGITAL VSURROUMfl Ш DIGITAL INPUT Г il II > I— TL / Г7А! \*±! I -I I ± П Jl Changing the recognition mode In rare cases, the unit may have trouble recognizing the digital signals on discs. With the PCM signals on CDs, this may cause the beginning of a track to be cut off. Engage the PCM FIX mode if this occurs. With DTS, the signals may not be recognized at all. Engage the DTS FIX mode if this occurs. This mode does not need to be changed under normal circumstances. Change it only if the unit appears to be having trouble recognizing the software you are playing. While the input source is selected and digital input is engaged: Press and hold [DIGITAL INPUT], The current mode is displayed. Press again to change the mode. Each time you press the button: AUTO — PCM FIX — DTS FIX t_1 When a FIX mode is on, the unit cannot process other signals. This may cause noise to be output. Select “AUTO" if this occurs. “AUTO” is reengaged when you turn the unit off. 16 Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674, 5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” and “DTS Digital Surround” are registered trademarks of Digita...