Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
® Press [BALANCE]. (D Press [—/L] or [+/R] to adjust. Tone You can adjust the level of the bass and treble. ® Press [TONE] to select “BASS” or “TREBLE”. (2) Press [-/L] or [+/R] to adjust bass/treble. For your reference • To adjust the tone The STEREO DSP mode must be on and input must be either analog or PCM signals. You cannot adjust the tone while the SOURCE DIRECT mode is on or if DVD 6CH INPUT is selected. 18 The radio INPUT SELECTOR jRECErER 0 TV VCR cwo TUNERiBAND o o o o o ô iwwara tape co ■a o o 1 2 3 □ □ □ 4 5 6 □ a □ 7 8 9 □ a 0 □ TQPUEKU VEW O o 0©0 O <23 o skip I—ftwmxi CH)EE)|QŒD STOP PAUSE PLAY (TinriR sauea çkumi vcuiee tnreo a giJ3_U J 9XOXf& —-~ □ Gi tZJTT I 1 2 3 ttUtER a a a □ n □ o ; ; 7 a 9 wtiCH ' i CD □ □ j CD “Tlïf5 0 ÎIMNTt*: x3 ! ! t) □ CB^f- SB ntUTB -a j □ □ O ; ¡¡Cl WC EFFECT IEVEL » ±-22 □ a a< tfBH TEST TOWS LUJtCS □ a □ □ tiXXO - TÏWL + ftMEQ \ a. a a!a; ' MM □ >. wo / PUCE SETUP □ □ CHANNEL ¡Ü1 (VENTER • a Manual tuning You can tune radio stations manually by selecting the station's frequency. © Turn [INPUT SELECTOR] to select “TUNER”. © Press [BAND] to select “FM” or “AM”. (3) Press [TUNING V or A] to select the frequency. Tuning intervals: FM-0.2 MHz AM-10 kHz For your reference DVD players can interfere with radio reception. Turn the DVD player off or move it further away from the antennas if this occurs. Direct tuning ©Press [TUNER/BAND RECEIVER]. The band changes each time you press the button. ©Press [DIRECT TUNING/DISC]. ©Press the numbered buttons to enter the frequency. e.g. To select 107.9 MHz, press [1] — [0] — [7] — [9] Tuning Intervals: FM-0.1 MHz AM-10 kHz • If you do not press a button while the cursor is flashing, the display returns to the frequency being received. • If the frequency has not been input correctly, “ERROR” will be displayed. Automatic presetting ©Tune to “FM 87.9 MHz”. © Press and hold [MEMORY]. The FM stations the unit can receive are preset in channels 1 to 30. © Tune to “AM 530 kHz”. © Press and hold [MEMORY]. The AM stations the unit can receive are preset in channels 21 to 30. (FM stations are replaced if any were preset in these channels.) During automatic presetting, the memory indicator (d) flashes and the frequency scrolls. The memory indicator and channel numbers are displayed for a second when a station is preset. The last station to be preset is displayed when presetting finishes. For your reference Even if the power supply cord is disconnected from the household AC outlet, the stations remain in memory for approximately one month. Manual presetting Preset the stations one at a time. ©Tune to the station. © Press [MEMORY]. © Press [TUNING V or A] to select a channel. © Press [MEMORY]. Selecting channels © Press [PRESET]. The channel number flashes for about 5 seconds. © Press [TUNING V or A]. Hold down the buttons to change channels faster. On the remote control Press [CHANNEL A or Vj. or Press the numbered buttons. For channels 1 to 9, press the corresponding number. For channels 10 or over, press [£10/ENTER], then the two digits, e.g. To select channel 21: [>10/ENTER] —* [2] — [1] Other settings DIMMER — Dim the display for better viewing in a darkened room Press [DIMMER] on the remote control. Adjusting the brightness of the display Choose a level between 1 (dim) and 5 (bright). The factory setting is LEVEL 2. CD Press and hold [A] and [B] at the same time to enter the setting mode. (2) Press [A] to select “DIMMER”. © Turn [INPUT SELECTOR] to select “LEVEL 1”, “LEVEL 2”, “LEVEL 3”, “LEVEL 4” or “LEVEL 5”. The brightness changes to show the level. © Press and hold [A] and [B] at the same time to exit the setting mode. DR COMP — Dynamic range compression Change this setting to listen to software recorded with Dolby Digital at low volume (such as late at night) and maintain audio clarity. It reduces the peak level in loud scenes without affecting the sound field. OFF: The software is played with the original dynamic range (factory setting). STANDARD: The level recommended by the producer of the software for household viewing. MAX: The maximum allowable compression (recommended for night viewing). (D Press and hold [A] and [B] at the same time to enter the setting mode. © Press [A] to select “DR COMP”. ©Turn [INPUT SELECTOR] to select “OFF”, “STANDARD” or “MAX”. © Press and hold [A] and [B] at the same time to exit the setting mode. A/D ATT - turn the A/D attenuator on if “OVER” lights frequently when using 2-channel analog input The factory setting is OFF. 0 Press and hold [A] and [B] at the same time to enter the setting mode. © Press [A] to select “A/D ATT”. ©Turn [INPUT SELECTOR] to select “OFF” or “ON”. © Press and hold [A] and [B] at the same time to exit the setting mode. Note • The setting affects all 2-channel analog input. • You can raise the volume to a maximum of -10 dB while A/D ATT is on. INPUT SELECTOR ...