Stimmen - 6, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Arcam Dateigröße: 1.2 mb Dateiname: Unterrichtssprache:

Set the internal selector switch to EXT INPUT position. Under these circumstances it has exacdy the same specification and performance as a Delta 290P power amplifier. Contact your dealer or Arcam for more details. ® PREAMP OUT - To use your Delta 290 as a pre-amplifier, connect PREAMP OUT to your power amplifier's input. Please note: the PREAMP OUT sockets are permanendy active. REMOTE CONTROL FUNCTIONS ■ Your Delta 290 amplifier is supplied with the Arcam CR25 "Handi Remote" infra-red remote control handset, which has buttons to allow the simple operation of other products. It is supplied with 2AA batteries -ensure these are inserted correcdy. The remote allows you to operate the Delta 290 plus some basic functions of an Arcamf or Philips based CD player, a remote controlled tuner (such as the Arcam Delta 280*), the Arcam Delta Black Box 500 DACC and an Arcam amplifier with remote control facility( the Alpha 6/ Alpha 6 Plus, Delta 110/110S pre amplifiers and the Xeta One/ Two Home Cinema amplifiers). Note: versions of the Delta 280 FM tuner manufactured before April 1995 will not respond to the programme up/down buttons on the "Handi Remote”. REMOTE MODE - The Delta 290 is fitted with an internal Remote Mode selector switch, which is factory-set to NORMAL. In NORMAL mode, the Arcam "Handi-Remote" or Arcam CR200 System Remote will synchronise the operation of any Arcam CD player or transport, cassette deck or remote control tuner with the LISTEN selector on the Delta 290, all at the touch of a single button. For example, using the remote in CD mode, press PLAY, and the CD player will start the disc and the LISTEN function selects CD. If this facility is not required, the internal selector switch should be set to UNIQUE. The LISTEN selector switch can still be operated by either remote control handset. The MUTE button mutes the speaker connections and pre-amp outputs. Both tape outputs however remain active. In MUTE mode the power LED will turn amber until mute is disabled by either pressing MUTE again or pressing volume -/+. Input selection may also be made via the CR25 and CR200 remote control handsets. Where fitted, the phono stage is selected with the PHONO button. All other inputs are made active when the relevant button is pressed. TAPE 2 may be chosen via the front panel switch but not by the remote control handset. Note: The SHIFT button does not initiate any functions within the Delta 290/290P. DELTA 290P POWER AMPLIFIER Please refer to drawing inside front cover. LOUDSPEAKER CONNECTIONS ■ The speaker terminals are colour coded red for positive and black for negative. These terminals are also labelled 'R' for the right channel speakers and 'L' for the left channel speakers. ©,@ Connect terminals © to your right speaker and terminals @ to your left speaker. ■ Connect the red cable termination to the red terminals and the other cable termination to the black terminal. If your speaker cable has bare ends, the positive conductor can usually be identified by a ridge or coloured marking. Ensure that no stray strands are allowed to touch another cable or the amplifier's casing. This can cause a short circuit and damage your amplifier! ©,© To drive a second pair of speakers, connect terminals © to the right speaker and terminals © to the left speaker. Except the Alpha One CD player, which uses a different remote control language. FRONT PANEL The Delta 290P can drive two pairs of loudspeakers, simultaneously if required, providing both pairs are rated between 8 and 16 ohms. Either pair can be selected using the switches labelled SP1 and SP2 on the front panel. To avoid overheating, the combined load impedance as seen by the amplifier should not fall below 4 ohms per channel. CONNECTING YOUR SOURCE COMPONENT © PWR AMP IN -Connect to your preamplifier outputs. ® PREAMP OUT: The 290P can be connected to provide two mono outputs from a single input. Using the U-link ® supplied, connect the PREAMP OUT sockets ® together. Utilising one Delta 290P per loudspeaker in this manner will allow bi-amplifying of bi-wireable loudspeakers. This is particularly beneficial for top quality stereo installations with a separate pre-amplifier, or for the left, centre and right channel loudspeakers in a five speaker Dolby Pro Logic system. Contact your Arcam dealer for more detailed information. ■ Daisy Chain - The Delta 290P is capable of driving further Delta 290P amplifiers (or any other power amplifier), to drive more speakers (eg. those in other rooms or triamplified speakers etc). Connect the extra power amplifier inputs to the PREAMP OUT outputs ® left to left, right to right. ©,© SP1 and SP2 - Pressing the SP1 switch turns on the speakers connected to the SP1 (upper) set of output terminals on the rear panel. Similarly the SP2 switch turns on the speakers connected to the SP2 (lower) set of output terminals. ■ Both the SP1 and SP2 switches can be turned on...

Herunterladen

Geben Sie zwei Ziffern: