Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Adcom Dateigröße: 1.2 mb Dateiname: f10dc314-432e-4622-9710-5a084e1ffc41.pdf Unterrichtssprache:

Note that with the volume at minimum it may be possible to still hear music very faintly. This is normal. VOLUME can also be operated by remote control (See Remote Control functions). © PROCESSOR/TAPE 2- This is a tape loop to enable monitoring of a recording on a 3 head cassette deck. It can also be used to enable line inputs to be sent to an external surround decoder such as the Arcam Xeta 2 for processing before being routed back to the amplifier. For playback of a cassette deck or if using an A/V processor attached to TAPE 2 press the button in. Note: PROCESSOR/TAPE 2 is not remote controllable. © DIRECT - Bypasses bass, treble and balance controls. This affects all inputs, and will generally give a small improvement in sound quality and a useful reduction in the level of background hiss. © BASS - Rotate clockwise to boost the bass response and anti-clockwise to cut the bass response. For a flat response leave in the central 'click' position. @ TREBLE - Rotate clockwise to boost the treble response and anti-clockwise to cut the treble response. For a flat response leave in the central 'click' position. @ BALANCE - Rotate clockwise or anticlockwise to move the position of the stereo image. This may be necessary if it is not possible to sit centrally between the speakers. In normal use leave in the central 'click' position. © SP1 - Selects or defeats the main pair of speakers. Push the button in to select. © SP2 - Selects or defeats the secondary pair of speakers. Push the button in to select. © HEADPHONES SOCKET - Accepts headphones rated between 8 ohms and 2kohms fitted with a 6.3mm stereo jack plug. If your headphones are fitted with a different plug contact your dealer for a suitable adaptor. If you wish to listen on headphones only, use SP1 and SP2 (if necessary) to mute the speakers. ■ The headphone socket is always switched on, irrespective of the positions -of switches © and ®. © REMOTE RECEIVER - Ensure the remote receiver is not obscured or commands from the remote control handset will not be received. © POWER - Switches the unit on and off © POWER LED - The LED above the POWER switch will initially glow amber. After a few seconds, it will glow green. When the LED glows amber, the speakers are disconnected and an internal protection circuit is activated or the unit has been muted by use of the remote control. If this LED glows amber during normal use it may be due to the amplifier overheating or an output overload. Check the amplifier is properly ventilated. Switch the amplifier off and wait for 2-3 minutes before switching on again. If the LED continues to glow amber, switch the unit off, remove all the speaker cables and switch on again. If the LED goes to green upon switch on then check the speaker and speaker cables for short circuits before reconnecting them. If the LED continues to glow amber with no speakers connected contact your Arcam TAPE RECORDING ■ Both sets of tape sockets (TAPE 1 and TAPE 2) are identical in sensitivity and suitable for use with almost any type of recorder (cassette, hi-fi VCR, reel to reel, DAT, etc.). ■ RECORDING (TAPE 1): Any input signal available on the Delta 290 may be routed to the TAPE 1 output sockets by using the RECORD selector to select the appropriate input. Set your tape recorder into its recording mode and the selected input will be recorded. Selecting the same input to listen to will not affect the signal sent out to the recorder and will now enable you to listen to the input being recorded. You may listen to another input whilst recording on TAPE 1 by use of the LISTEN selector. If your tape recorder is a 3 head design, this will allow A-B monitoring of the actual recording while it is taking place. Switching the listen switch between the original source and TAPE 1 during recording will then allow you to make a true 'before and after1 (A-B) comparison. ■ PLAYBACK (TAPE 1): Set LISTEN to TAPE 1 and set your tape recorder in its playback mode. ■ RECORDING AND PLAYBACK, TAPE 2: Proceed as above, except use the TAPE 2 sockets and select the input to be recorded by use of the LISTEN selector. Use the PROCESSOR/TAPE 2 button when monitoring or playing back the recording. Do not move the listen selector whilst recording or you will lose the signal. ■ TAPE TO TAPE DUBBING: The Delta 290 allows 2 way tape dubbing (copying) from TAPE 1 to TAPE 2 or For example, to copy from a recorder connected to the TAPE 2 sockets to a recorder connected to TAPE 1, first switch the RECORD selector on the Delta 290 to TAPE 2. This routes the TAPE 2 signal to TAPE l's output. Then set the first tape recorder into its 'record' mode and the second to 'playback' mode to enable the transfer to take place. If you wish to monitor the transfer while it is taking place switch LISTEN to TAPE 1. To record from TAPE 1 to TAPE 2 set listen to TAPE 1. To monitor push the PROCESSOR/TAPE 2 button in. PRE/POWER CONNECTIONS ...

Herunterladen

Geben Sie zwei Ziffern: