Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Use a piece of cardboard as a shield to catch overspray at the edges of the work to protect other surfaces Use masking tape to cover other areas if needed User -maintenance Instructions DAILY CLEAN-UP Local codes may require specific cleaning methods and equipment Follow local codes and paint manufacturer’s recommendations for the use and disposal of spray materials and solvent Clean spray gun immediately after use. Paint and other materials dry quickly in the small passages rendering gun useless due to the difficulty of removing hardened paint from the passages inside the gun. NOTE: In the instructions below, the use of the word “solvent” refers to the specific solvent for the material used (example: lacquer thinner for lacquer, etc ) 1 . Remove and empty the canister; then rinse with a solvent recommended for the paint or other material used 2 Refill canister with clean solvent and attach to the gun Spray solvent through the gun while shaking the gun vigorously Wipe the gun exterior with a solvent soaked rag Repeat until the gun is clean Gravity Feed Spray Gun 3 Remove the air cap and soak in solvent until clean Use a small brush for stubborn stains if necessary Toothpicks or small brushes may be used to clean air passages; however, NEvER USE mETAL OBJECTS TO CLEAN PRECISELY DRILLED PASSAGES. DAmAGED PASSAGES WILL CAUSE ImPROPER SPRAYING4 Clean gaskets with a solvent soaked rag To prevent equipment damage, DO NOT ImmERSE GASKETS OR SPRAY GUN BODY IN SOLvENTS5 After using water to clean out water based paints or materials, spray mineral spirits through the gun to prevent corrosion 6 Use a non-silicone oil on all moving parts when reassembling Use Vaseline® or light grease on all threaded connections prior to storage 7 Clean and flush gun thoroughly to neutralize any contaminants corrosive to the spray gun PERIODIC CLEAN-UP Due to improper cleaning and paint it may be necessary to inspect and clean the internal parts and the gun body 1 . Examine openings in air cap and fluid tip If clogged, remove any o-rings and soak the air cap or fluid tip in solvent 2 . A brush or toothpick or something similar may be used to dislodge the dried paint from holes and passages NEvER USE mETAL OBJECTS TO CLEAN PRECISELY DRILLED PASSAGES. DAmAGED PASSAGES WILL CAUSE ImPROPER SPRAYING 3 . Remove and check the fluid needle for excessive wear at the tip and straightness ImPORTANT: If the needle tip is worn more on one side than the other, either the needle is bent or the gun body has been dropped or knocked out-ofline There are no adjustments that can be made to a bent gun body Test the needle by rolling on a flat surface Replace if necessary 5 Operating Instructions Gravity Feed Spray Gun User -maintenance Instructions (Continued) 4 . Check and replace any damaged o-rings and seals O-rings and seals can be wiped clean but not soaked in solvent 5 . Unscrew packing nuts and replace the packing ONLY if a leak will not stop when the nut is tightened (See Figure 5) Do not over-tighten a packing nut because this will restrict movement of the needle 6 . Re-assemble in reverse order of above and use a non-silicone oil on moving parts Apply Vaseline® or light grease on threaded joints and hose connections TECHNICAL SERvICE STORAGE Please call our Tool Hotline at 1-800-1 When not using spray gun, 543-6400 with any questions regarding turn the fluid adjustment knob the operation or repair of this tool or counterclockwise to open which for additional copies of this manual will reduce spring tension on needle fluid tip TOOL REPAIR 2 . Spray gun mUST BE well cleaned Only qualified personnel should repair and lightly lubricated the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently Troubleshooting Chart Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Symptom Possible Cause(s) Corrective Action Right or left 1 Holes in left or right side of the air cap 1 Clean Use only non-metallic pick heavy spray are plugged pattern 2 Dirt on left or right side of fluid tip 2 Clean Top or 1 Dried material at top or bottom of fluid 1 Clean bottom tip heavy spray 2 Loose air cap or dirty seat 2 Clean and tighten pattern 3 Air cap plugged 3 Clean Use only non-metallic pick Split spray 1 Fan pattern open too far 1 Partially close the pattern adjustment pattern 2 Fluid turned in too far 2 Increase fluid 3 Atomization air too high 3 Reduce atomization air pressure Center 1 Fan adjustment partially closed 1 Open fan pattern adjustment heavy spray 2 Material too thick 2 Thin to proper viscosity pattern 3 Atomization pressure too low 3 Increase atomization pressure Sputtering 1 Material level too low 1 Refill spray 2 Container tipped too far 2 Hold more upright 3 Loose fluid inlet connection 3 Tighten 4 Loose ...
Dieses Handbuch ist für folgende Modelle:Farbspritzpistolen - IN270101AV (5.69 mb)