Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Hitachi Dateigröße: 1023.02 kb Dateiname: 93974.pdf Unterrichtssprache:

13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired. 14. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any trigger does not operate properly. 15. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 16. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 17. Use proper size and type extension cord. If an extension cord is required for the compressor, it must be of the proper size and type to supply the correct current to the compressor without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the compressor. Check your compressor’s manual for the appropriate size cord. 18. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician and the unit must be thoroughly cleaned out after every use. Improper cleaning of the Spray Gun is a common reason for the Spray Gun to jam or not perform properly. 19. Compressed air only. Never use combustible gas as a power source. Never exceed the recommended operating pressure of the any of the parts (i.e. hoses, fittings, gun) of the Sprayer system. 20. Do not spray near open flames, pilot lights, stoves, heaters, the air compressor, or any other heat source. Most solvents and coatings are highly flammable, particularly when sprayed. Maintain a distance of at least 25 feet from the air compressor. If possible, locate the air compressor in a separate room. Do not smoke while spraying. Page 3 SKU 93974 For technical questions, please call 1-800-444-3353 21. Read all of the information concerning coating products and cleaning solvents. Chlorinated solvents (e.g. 1-1-1 Trichlorethylene and Methylene Chloride, also known as methyl chloride) can chemically react with aluminum and may explode. Many paint sprayers contain aluminum. If you have any doubt about potential chemical reactions, contact the solvent or coating manufacturer. 22. Materials used when painting or cleaning may be harmful or fatal if inhaled or swallowed. Only use in an area with adequate ventilation. Use a respirator or mask when painting or using cleaning solvents. 23. Never release the sprayer lid while the cup is pressurized. 24. Industrial applications must follow OSHA requirements. 25. Never point a spray gun at a person or animal. Serious injury could occur. 26. Spraying hazardous materials may result in serious injury or death. Do not spray pesticides, acids, corrosive materials, fertilizers, and toxic chemicals. 27. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code § 25249.5, et seq.) Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Page 4 SKU 93974 For technical questions, please call 1-800-444-3353 Unpacking When unpacking, check to make sure the parts listed on pages 14 and 16 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Air Connection Spray Gun 1/4” NPS For best service you should incorporate a regulator, and inline filter, as shown in the diagram above. Hoses, couplers, regulators, and filters are all available at Harbor Freight Tools. Note: Compressor pumps discharge condensed water, oil, or other contaminants along with the compressed air. Condensation cause “fish eyes” to appear in paint patterns. To avoid this problem, install water/oil removal filters and controls (not included) as close to the Spray Gun as possible. If run through the Gun, water and oil will cause damage. 1. You will need to prepare a 1/4” air connector to connect to the air inlet on either the Large or Small Sprayers. First, wrap the Air Inlet (40 or...

Herunterladen

Geben Sie zwei Ziffern: