Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Alarm Volume. The alarm volume is set to Select CLOCK & ALARM > ALARM. the same level as the ringer volume. If the Press OK. ringer is off, the alarm volume is set to Select ON ONCE or ON DAILY. level 1. Press OK. Enter the alarm time. 14.2 Easy call Tip Easy call allows you to dial out a 12 3 4 You can set the time format to 12-hour programmed number by pressing any or 24-hour. See “Setting the date and handset key (except BACK). time format” on page 16. Press OK. 14.2.1 Activating easy call • The alarm is set and the icon 5 Press m. 12 34 displays. 14.1.2 Turning off the alarm Select ADVANCED SET > EASY CALL > MODE. Press OK. Select ON. Press OK. Enter the easy call number (if it is 14.1.2.1 When the alarm rings not set previously). Press OK. 1 Press e or OK to turn off the • The setting is saved. alarm. Pressing other keys cannot ! Warning stop the alarm. When easy call is activated, you will not Note be able to make emergency calls. If you do not press any key after the alarm clock rings for 1 minute, it will turn off automatically. 42 Extra Features 14.2.2 Setting the easy call number 14.4 Missing handset(s) 1 Press m. 2 Select ADVANCED SET > EASY CALL > NUMBER. Press OK. 3 Enter the easy call number. Press OK. • The setting is saved. 14.2.3 Deactivating easy call 1 Press BACKc during standby. • The easy call menu displays. 2 Select OFF. Press OK. • The setting is saved. 1 Press V on the base station. • All the handsets connected to this base station ring. 2 Press V on the base station again to stop locating handsets. • All the handsets stop ringing OR Press any key on the handset to stop the ringing for that handset. 14.3 Keypad lock You can lock the keypad to prevent accidental presses on the handset while you are carrying it around. 14.3.1 Locking the keypad 1 Press and hold * during standby. The keypad is locked. • KEYS LOCKED is displayed. Note Calls. You will not be able to make any calls including emergency calls when the keypad is locked. You can still answer incoming calls. The keypad will be unlocked during the call, and then it will be re-locked automatically after you finish the call. 14.3.2 Unlocking the keypad 1 Press and hold *. • The keypad is unlocked. Extra Features 15 The System 15.1 Registering handset(s) The procedures described below are the procedures you will find in your handset. The procedures may vary according to the handset you want to register. In this case, refer to the manufacturer's instruction of the additional handset. Additional handsets must be registered to the base station before you can use them. Your base station can register up to 5 handsets. 1 Press m on the handset you want to register. 2 Select ADVANCED SET > REGISTER. Press OK. 3 Follow the handset's screen instruction. • Registration shall be completed in less than 2 minutes. The base automatically assigns a handset number to the handset. Note If no base is found within a certain period, your handset displays a notification message. Repeat the above procedure if registration failed. 15.2 Un-registering a handset Use one handset to unregister another handset that shares the same base station. 1 Press m. 2 Select ADVANCED SET > UNREGISTER. Press OK. 3 Select the handset (number) you want to un-register. Tip Handset Number. The handset number displays beside the handset name during standby. 5 Press OK. • The handset is un-registered. 15.3 Changing your PIN The system PIN is used for registration and protecting access rights to some of the menus. The pre-set PIN is 0000. You can personalize your PIN for greater security. 1 Press m. 2 Select ADVANCED SET > CHANGE PIN. Press OK. 3 Enter the current system PIN. Use BACK to make corrections. Press OK to confirm the system PIN. 4 Enter the new system PIN. Press OK. 5 Enter the new system PIN again for verification. Press OK. • The setting is saved. Note Forgotten PIN. Write down your PIN and save it for future use. If you have forgotten the PIN, reset your phone and your PIN code will be restored to the factory pre-set PIN (0000). To reset your phone, see “Restoring default settings” on page 44. 15.4 Restoring default settings You can reset your phone settings to the original factory settings. 1 Press m. 2 Select ADVANCED SET > RESET. Press OK. The System • The handset displays a confirmation request. 3 Press OK to confirm. • All settings have been reset. Note After reset, your handset's power switches off. It will switch back on in a few seconds after updating all the settings. All handsets return to the standby mode after reset. To see a list of default setting, see “Default (pre-programmed) settings” on page 46. The System 16 Default (pre-programmed) settings Language English Handset Name PHILIPS Date Unchanged Date Format MM/DD Time Unchanged Time Format 12-hour Alarm Off Phonebook List Unchanged Auto Hang Up On Flash Time Long Quick Dial [Empty] Easy Call Mode Off Easy Call Number [Empty] Call Barring Mode Off Call Barring Number [Empty] First Ring On Network ...