Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Fotos und technische Daten Binatone Active XA1001 |
Anleitung Zusammenfassung
C). 2. Insert a 9V battery (6F22 type) into the battery compartment [35] on the base unit [28] then close the compartment [35] with the cover [36] and fasten the cover [36] with the screw [37] (see Fig. D). 3. Connect one end of the phone line cord [42] to the phone line jack [40] at the base unit [28] rear side, and the other end of the phone line cord [42] to the phone line socket. 4. Insert the AC adapter [41] cable plug into its jack [39] at the base unit [28] rear side. Insert the AC adapter [41] plug into a wall outlet of your 220V electric mains (see Fig. E). 5. Place the handset [1] on the base unit [28] (see Fig. B). Before initial use you should fully charge the battery for about 15 hours. When you place the handset [1] on the base unit [29] for charging, you should hear a short beep. 7 Butaio’He. ENGLISH Notes: 1. When you are not using the phone (for example, when you are not at home), place the handset on the base unit so that the battery will always be charged. 2. To ensure the maximum operating distance and noise-free operation, install the base unit in a convenient location away from electrical appliances such as a refrigerator, personal computer, TV or another phone. 3. You can dial a phone number in the pulse or tone mode. To choose the appropriate mode, just slide the P-T switch [38] to the "Tone" position for tone dialing and to the "Pulse" position for pulse dialing. The handset of the ACTIVE XA1001 phone will not operate in case of a power failure. Therefore, for essential communications such as medical emergencies you should have another phone that does not requires an electric mains supply and will be operable in case of a power failure. If you are moving during a conversation and noise interferes with the conversation, this may be caused by some interference, the source of which is located between the handset and base unit, for example, you may be too close to another phone or other electric equipment. Move to another location as far from the interference source as possible and press the CH button [10]. If you not do this, the call may be disconnected. Making calls 1. Press the PHONE button [3], the indicator light [2] lights up. 2. Dial a phone number. Answering calls When the phone rings, press the PHONE button [3]. Note: For noise-free conversation, it is necessary to extend the antennas [11] and [29] on the handset and base unit. Finishing calls To finish a call, press the PHONE button [3], the indicator light [2] will go out. Redialing the last dialed number 1. Press the PHONE button [3], the indicator light [2] lights up. 2. Press the LNR/P button [6] and the last dialed number will be automatically redialed. (You can redial a number consisting of no more than 32 digits.) Microphone mute You can turn off the handset microphone during a conversation. The calling party will not hear you. 1. Press the SEC button [4]. (When the microphone is turned off, the indicator light [2] flashes and the handset buttons are locked.) 2. To cancel the microphone mute, press the SEC button [4] once again. Inserting a pause in the dialed number When saving a phone number in the phone memory, press the MAKING CALLS SmaioHe. 8 LNR/P button [6] where the pause is needed (if a long pause is necessary, then press the LNR/P button [6] several times). For example, if you are dialing through a PBX and should dial '9' to access the PBX trunk, press the LNR/P button [6] after entering '9' and then enter the number you want to store. Storing a number in the phone memory You can store 16 phone numbers in the phone memory, of up to 20 digits each. 1. Press the MEM button [8], the indicator light [2] starts to flash. 2. Enter the number you want to store in the memory. 3. Press the MEM button [8] once again. 4. Enter a two-digit number (01 to 16) under which you want to store the entered phone number. 5. After completing the above steps you will hear a beep and the indicator light [2] will go out. Dialing a number stored in the phone memory 1. Press the PHONE button [3], the indicator light [2] lights up. 2. Press the MEM button [8]. 3. Enter the two-digit number (01 to 16) corresponding to the phone number you want to dial Note: You can store in the phone number just a part of a phone number (for example, the international telephone code) and combine memory dialing with normal phone number dialing. Deleting a number stored in the phone memory 1. Press the MEM button [8], the indicator light [2] starts to flash. 2. Press the MEM button [8] once again. 3. Enter the two-digit number (01 to 16) corresponding to the phone number you want to delete. 4. After completing the above steps you will hear a beep and the indicator light [2] will go out. Changing the ringer tone 1. Press the VOLUME/RINGER 4/^ A button [7] (the ringer tone cannot be changed during a call), the indicator light [2] lights up. 2. To select the desired ringer tone, press one of the buttons 1...