Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
If the clock is not set or corrected automatically after you change the location or direction of the radiocontrolled clock antenna, wait a while and see if you get better reception at a later time. Automatic updating of time data The Dream Machine is equipped with the Clock Auto Adjust system that automatically receives time signals during the night, when reception is best. The system makes nine corrections every hour from 8 p.m. to 4 a.m. During automatic operation, “ ” does not flash. If the Clock Auto Adjust system is unable to receive time signals for more than 24 hours “ ” goes off. In such a case, press CLOCK AUTO ADJUST to initiate Clock Auto Adjust manually and change the position or direction of the radio-controlled clock antenna for improved reception. Note Automatic updating cannot be manually cancelled. On daylight Saving Time adjustment The Clock Auto Adjust system automatically switches the clock indication to Daylight Saving Time (summer time), and back, at the necessary time of the year. “ ” will be displayed when the clock is in Daylight Saving Time. Note According to reception conditions, the actual adjustment to or from Daylight Saving Time by the Clock Auto Adjust system may be done later than the exact moment of transition in the yearly calendar. To Set the Clock and Date Manually 1 Plug in the clock radio. The display will flash “AM 12:00”. 2 Press CLOCK for a few seconds. You will hear a beep and the year will start to flash in the display. 3 Press Jog lever v (up) or V (down) until the correct year appears in the display. 4 Press ENTER/BRIGHTNESS. 5 Repeat steps 3 and 4 to set the month, day, hour, and minute. After setting the minute, press ENTER/ BRIGHTNESS to start the counting of the seconds, and you will hear two short beeps. • To set the current time rapidly, hold down Jog lever v (up) or V (down). • In step 5, when you press ENTER/BRIGHTNESS after the minute setting to activate the clock, the seconds start counting from zero. • When the alarm setting mode is entered, the clock cannot be set. Note The clock is set to automatically receive time signals and will continue to do so even if it is manually reset. To display the year and date Press SNOOZE/DATE/SLEEP OFF once for the date, and within 2 seconds press it again for the year. The display shows the date or year for a few seconds and then changes back to the current time. To set the brightness of the backlight If you cannot see the display clearly, press and hold ENTER/BRIGHTNESS to set the desired brightness (high, middle or low). Changing AM Channel Step The AM channel step differs depending on area. The channel step of this unit is factory-set to 10 kHz to change the setting as shown below to be able to listen to the radio. Area Channel step North and South America 10 kHz Other countries/regions 9 kHz 1 Plug in the clock radio. Press OFF/ALARM RESET to turn off the power. 2 While holding down OFF/ALARM RESET, keep pressing ON/BAND for more than 5 seconds. The AM channel step will be changed. If you proceed to step 2 again, the channel step changes again. Notes • When the AM channel step is changed, the preset stations for AM will be initialized. • When the AM channel step is changed, the FM channel step also will be changed. Playing the Radio —Manual Tuning 1 Press ON/BAND to turn on the radio. The display shows the band and frequency for a few seconds and then changes back to the current time. 2 Press ON/BAND repeatedly to select the desired band. Each press changes the band as follows: AM FM1 FM2 When using FM1 or FM2 preset mode, you may listen to the radio on either mode. (See “Presetting Your Favourite Station”.) 3 Use TUNING + or – to tune into the desired station. The FM frequency advances or reverses in 0.1 MHz channel steps and the AM frequency in 10 kHz channel steps. Two short beeps sound when the minimum frequency of each band is received during tuning. 4 Adjust volume using VOLUME. • To turn off the radio, press OFF/ALARM RESET. • To check the station being received, press TUNING + or – or ON/BAND lightly. The display shows the band and frequency for a few seconds and then changes back to the current time. Improving the Reception FM: Extend the FM wire antenna fully to increase reception sensitivity. AM: Rotate the unit horizontally for optimum reception. A ferrite bar is built in to the unit. Do not operate the unit over a steel desk or metal surface, as this may lead to interference of reception. Presetting Your Favourite Station —Preset Tuning You can preset up to 10 stations in FM (5 stations in FM1, 5 stations in FM2), and 5 stations in AM. Presetting a Station 1 Follow steps 1 to 4 in “Playing the Radio” and manually tune into the station you wish to preset. 2 Hold down the desired STATION•SELECT/PRESET button until you hear two short beeps. Example: To preset AM 1 260 kHz onto preset 2 button. The display shows the frequency for a few seconds and then changes back to the current time. To preset another...
Dieses Handbuch ist für folgende Modelle:Radios - DREAM MACHINE ICF-C275RC (661.83 kb)