Anleitung Audiovox, modell SIR-HK1
Hersteller: Audiovox Dateigröße: 67.24 kb Dateiname: 9494fac1-2b34-42cc-8b75-a52ea3dda665.pdf
Unterrichtssprache:
|
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Anleitung Zusammenfassung
If this condition persists after corrective action, consult your dealer or experienced installation facility. 3. By adhering to these warnings and safety considerations, serious accidents and/or personal injury can be avoided. 128-6814 3 of 8 Contents SIR-HK1 Installation/Wiring Precautions Install Manual Audio Cable P/N 1286814 (P/N 112B3293) 1. Make sure the adapter cable is not connected to an AC wall outlet until all interconnections have been made and verified. The adapter power cable should be connected last. 1 pc. Antenna 1 pc. 2. Do not install the unit in the locations exposed to (P/N 118C1125) direct sunlight or in areas subject to extreme Cradle HK1 temperatures. (P/N 136D3472) 3. Incorrect installation may cause damage to the system. 4. During antenna placement/installation, refer to 1 pc. the Antenna Aiming procedure outlined in the DC Power Adapter Shuttle User Guide, SIR-PNP1(128-6812). (P/N 136C3467) 1 pc. -4 128-6814 4 of 8 1 pc. Setting Up and Installing Your Kit NOTE: The SIRIUS® signal can be received and processed virtually anywhere as long as there are no obvious satellite signal obstructions such as high terrain, trees, overhangs, etc. 1. Cabling Interconnections You can begin to enjoy Sirius® Satellite Radio as soon as the Shuttle and home Kit installation are complete. Set up your Audiovox Shuttle using the following installation instructions, or enlist the help of a professional installer. 2. Installing/Positioning the Antenna For best reception, the supplied antenna should be placed near a window; some repositioning may be required to achieve optimum results. The following guidelines are recommended: a. In a major city, where Sirius ground repeaters are present, you can usually place the antenna away from a window and still achieve the desired results. -5 Interconnect Diagram SHUTTLE CRADLE HK1 SAT. RF CONNECTOR SHUTTLE ANTENNA AUDIO CABLE TO AUXILIARY AUDIO INPUT OF RADIO OR ENTERTAINMENT SYSTEM TO AC WALL OUTLET DC POWER ADAPTER 128-6814 5 of 8 b. You can also place the antenna outside (on the roof structure), provided it is clear of any overhead obstructions. NOTE: Because of the orbiting characteristics of the Sirius Satellites, the strength of the received signal may change over time. In most cases however, the signal should be available continuously. If you experience a loss of signal or audio, reposition the antenna inside the home or outside as necessary. 5. Installing the Shuttle on the Cradle Place the Shuttle in the cradle so that the Shuttle connectors are lined up; use the SAT and TERR RF connectors as guides. Then gently press in on the bottom of the Shuttle to engage the connectors. -6 SAT. (MAIN) RF CONNECTOR TERR. RF CONNECTOR 16-PIN SYSTEM CONNECTOR 7. Mounting the Antenna The antenna should be placed on a relatively flat surface whenever possible. To mount the antenna: a. b. Plug the antenna into the SAT. (MAIN) connector on the back of the cradle. Place the antenna at the preferred location inside or outside the home. 128-6814 6 of 8 c. Apply power to the Shuttle system as outlined in the associated User Guide and obtain an audio output. If no audio is heard, move the antenna to different positions on the surface until an audio output is heard. This is the desired antenna position and should be marked with masking tape or by another non- scratch method. f. g. If the antenna is mounted outside, route the cable from the antenna position to the interior of the home, working the cable through the basement,under a window sill, etc.; make adjustments and take up slack whenever necessary. Plug the antenna cable into the SAT (MAIN) connector on the back of the cradle. d. e. After determining the optimum position, turn off Shuttle power, disconnect the power adapter from the wall outlet receptacle and disconnect the antenna cable. Plan the routing of the antenna cable to the Shuttle RF input. Make sure you avoid any obstructions that could crimp, kink or twist the cable; use protective grommets wherever rough openings are encountered. j. k. l. Plug the female end of the AC cable into the DC adapter; then plug the DC Adapter jack into the DC 12V receptacle on the cradle. Plug the other end of the AC cable into a 110volt wall receptacle; the integral power LED in the Shuttle power button ( ) will light red. You are now ready to enjoy Sirius programming within your home. -7128- 6814 7 of 8 AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of d...