Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
(OUT) Video Cable S-Video Cable (IN) SELECTING AUDIO/VIDEO INPUT When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by pressing [INPUT SELECT] on the remote control or [SELECT] on the main unit. The input mode changes by pressing the button as following: INPUT TV channel VIDEO1 VIDEO2 SELECT VIDEO1 input OR Plug the incoming cable into the ANT jack on the rear of the TV. *NOTE (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company. Rear of this TV OR Incoming cable from home Antenna / Cable Company (No Cable Box) Incoming cable from Cable Company or Satellite Antenna Cable Box or Satellite Box* Cable TV signal OR Antenna IR transmitter To send infrared ray (IR) signal Note: . You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.) Tilt Stand Adjust the stand to change the angle of TV (-5° ~ 10°). -5° 10° TILT STAND UNPACKING Do not bend from this side. The stand of this TV is folded when you purchased. Place this TV face-down on a flat surface covered with the soft cloth. Bend the stand slowly to forward until it clicks. If you want to fold the stand again, insert a thin rod into the hole in the right side of the stand as illustrated, bend the stand backward while you keep pushing the hole. +100 button Press to select cable channels higher than 99. Notes: . In case no channel can be received by the channel scanning, “NO TV SIGNAL” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again. . If those settings do not work properly, please call our help line on the front page of this owner's manual. 2 If the TV screen shows snow noise and there is no operation for more than 5 seconds, “HELPFUL HINTS” appears. Follow the instructions listed onscreen. Select the desired language according to the screen indication. After that, the TV performs “AUTO PRESET CH” to scan channels available for the broadcasting in your area. When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel. SELECT LANGUAGE ENGLISH NEXT:PRESS CHK ESPANOL DESPUES:PRESIONE CHL FRANCAIS APRES:PRESSEZ VOLX – INITIAL SETUP – PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT. THEN PRESS CH K, IN ORDER TO PERFORM “AUTO PRESET CH ”. INITIAL SETUP When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed. The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed. 1 - HELPFUL HINTS - 1. PLEASE CHECK TO SEE IF THE ANTENNA/CABLE/SATELLITE IS PROPERLY CONNECTED. 2. DID YOU PERFORM “AUTO PRESET CH” ? 3. PLEASE REFER TO FRONT PAGE OF THE OWNER’S MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION. Cables not included MENU VOLUME CHANNEL SELECT POWER POWER button To turn TV on/off VOLUME X/Y buttons To adjust volume SELECT button To select TV or external input CHANNEL K/L buttons To select channels MENU button To view on-screen menu Infrared Sensor Window Note: . The display will disappear automatically after 10 seconds unless you press any buttons. [TEXT MODE (TEXT1, TEXT2)] . TEXT1 and TEXT2 display half-screen text by scrolling (such as a channel guide, schedule or announcement). OPERATIONS (Continued) OPTIONAL SETTINGS PICTURE ADJUSTMENT 1 MENU m VOL - TV SET UP - PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE CHANNEL SETTING 1 MENU o p CH - TV SET UP - PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE MENU o p CH - TV SET UP - PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE m VOL 2 m n VOL Select the desired language 3 MENU To exit the menu o p CH m VOL - CHANNEL SET UP - ADD/DELETE CH (TV) AUTO PRESET CH NO TV SIGNAL LANGUAGE SELECTION 3 1 2 MENU o p CH - TV SET UP - PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE m VOL o p CH - CHANNEL SET UP - ADD/DELETE CH (TV) AUTO PRESET CH Select the channel you wish 4 m n VOL Notes: . If closed captioning is not broadcasted, you cannot receive it and nothing is displayed. . When your TV receives a special effects playback signal (i.e., Search, Slow and Still) from a VCR’s video output channel (CH3 or CH4), the TV may not display the correct caption or text. . Captions and texts may not match the TV voice exactly. . Interference may cause the closed caption system not to function properly. . The caption or text characters will not be displayed while the menu display or functions display is shown. . If a black box appears on the screen, this means that the TV is set to TEXT mode. To clear screen, select [CAPTION1], [CAPTION2...