Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
help you use your machine in a fast and safe way, • Please read the User Manual before installing and starting your machine. • Particularly follow the instructions related to safety. • Keep this User Manual within easy reach, You may need it in the future. • Please read all additional documents supplied with this machine, Please note that this User Manual may be applicable for several other models, Differences between models will be identified in the manual. This product has been produced in } environmentally friendly, modern facilities Contents 1 Key Features 2 Installations >3-5 3 Operation >5-9 4 Auxiliary Features >9 5 Specifications >10 6 Safety >10-11 7 Cleaning and Care >11 1 @> Cautions • Do not subject the device to severe impact or drop it from high position. • Do not use the player in extreme hot or cold, dusty or damp field. Do not expose it to direct sunshine. • Back up the data frequent^ In case of accident data loss. • Avoid using the player in strong magnetic field. • Keep the device away from water or other liquids. In the event that water or other liquids enter the device, power off the product immediately, take out the battery and clean the device. |U Key Features_ • Do not use chemical solution to clean the device in order to avoid corrosion. Clean it with a dry cloth. • We are not responsible for the damages or lost data caused by malfunction, misusing, repairing the device or battery replacement. • Do not attempt to disassemble, repair or modify the product, or it will be out of guarantee. • The design of the player or actual display may be different from what is shown in this manual. It should be subject to the actual display or design. Ear/Mic/Charge jack Press to send Ringing tone to CALL buttonother PMR units. UP/DOWN Buttons Press to change channels, volume, and to select settings during programming. Press to change To switch between Modes. MIC (Microphone) Speaker Private mobile radio with twin charger Antenna LCD Screen Displays the current channel selection and other radio symbols. PTT (PUSH to TALK) button Press and hold to transmit PWR(POWER) Button Press and hold to turn the unit ON or OFF. MENU Button LCD Screen CTCSS SC TX DCS RX UID’O-it ^L)illl DCMVOX 8 Channel Number. Changes from 1 to 8 as selected by the user. CTCSS Code. Changes from 1 to 38 as selected by the user. HID" Displays the Battery change level. When the bars are reduced, the battery needs recharging. TX Displayed when transmitting a signal. RX Displayed when receiving a signal. DCM Displayed when the Dual Watch function is turned On DCS Displayed when the Digital Code System is turned On VOX Displayed when the VOX feature is enabled. SC Displays when the PMR Is scanning all channels. O-w Displayed when the Key Lock feature is activated. ■ Ill Displays the current Speaker volume level. A Displays when the call signal is ON. o Displays when the vibrator function is activated. □ Installations Removing the Belt Clip a. Pull the Belt Clip latch forward (away from the PMR) b. While pulling the Belt Clip latch, push up the Belt Clip as shown in Figurel. Installing the Belt Clip a. Slide the Belt Clip into the slot as shown in Rgure2. A "dick” indicates the Belt Clip is locked into position. Installing the Battery pack Figure 3 Figure 4 o o t o o Belt Clip latch Figure 1 Caution: Observe the proper battery polarity orientation when installing batteries. Incorrect positioning can damage both the batteries and the unit. a. Slide down the Battery Compartment Cover. b. Install the rechargeable battery pack by following the orientation as shown In Figure 3 (the arrow Is showing and pointing upward.) c. Replace the Battery Compartment Cover. See Figure 4. Important Read these Safety Warnings before you charge the batteries. When ptacing the PMR In the charger, use only the power supplies listed in the user instructions supplied with the PMR. Don't try to recharge non-rechargeable batteries.Make sure the battery compartment cover is securely locked in place when you are charging the batteries. Dispose of used batteries safely and in a way that will not harm the environment- never try to bum them or put them anywhere, they could get burnt or punctured. Don’t leave dead batteries in your PMR units. They might leak if you do. Charging the battery pack a. Insert the small plug on the end of the mains adaptor into the Power-in Connection Jack at the back of the desktop charger. b. Plug the mains adaptor into a 240V AC, 50Hz main socket with the switch on the socket set to OFF. c. Switch ON the main socket. The PMR must be charged using the mains adaptor prowded. Using any other adaptor will result in non-compliance with EN60950-1 and will invalidate any approvals & warranty. d. Place the PMR units in the charge cradle in an upright position and facing outward. The Charge LED indicators will light up. e. It takes about 10 hours to fully rech...