Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Then talk y into the loudspeaker grill. ALK button on the Parent Unit is being pressed, no sounds y Unit can be heard on the loudspeaker of the Parent Unit. ALK button when finished or when you wish to hear your Explanation of features Monitoring baby silently ENGLISH 11 SC484_book.qxd 23-09-2004 17:51 Pagina 11 alking back to comfort your baby ent Unit, press and hold the TALK button (24) until the DECT STEM LINK lights (3 and 15) of both units blink (green). Then talk y into the loudspeaker grill. ALK button on the Parent Unit is being pressed, no sounds y Unit can be heard on the loudspeaker of the Parent Unit. ALK button when finished or when you wish to hear your Explanation of features Monitoring baby silently ENGLISH 11 SC484_book.qxd 23-09-2004 17:51 Pagina 11 olume of the Parent Unit to the lowest level, using the buttons (13). + > The sound-level lights (25) visually alert you to baby’s sounds. The more sound your baby makes, the more lights light. > When no sound is detected, all lights will be off. > If the volume of the Parent Unit is set to Off, the Parent Unit will beep as soon as the second sound-level-light (25) lights red. Checking that the units have established a connection • Check that the DECT SYSTEM LINK light (15) on the Parent Unit lights continuously (green) to confirm that the connection between both units is reliable. > When losing the link it will take about 8 seconds before the system link led starts blinking.After another 30 seconds,the led blinks read and the alarm sound is heard on the parent unit.When re-establishing the link it takes maximally 30 seconds to confirm the link again. Switching the night lights on and off • Press the button (2) on the Baby Unit to switch on the night lights. • Press the button again to switch off the night lights. > The nightlights dim and gradually switches off. Note: Switch off the night lights when operating the Baby Unit on batteries to conserve power. Paging the Parent Unit If the Parent Unit is misplaced and the volume is switched off, you can use the Page button on the Baby Unit to locate the Parent Unit. • Press the page button (1) on the Baby Unit. > The Parent Unit will automatically reset to medium volume level and paging alert will sound. • To stop the paging alert, press the Page button again or any button on the Parent Unit. Operating range • The SBC SC484 baby monitor has an open air operating range of up to 300 metres.Walls, ceilings, large objects and even glass will decrease the operating range. Depending on your local circumstances, the operating range can decrease down to approximately 50 metres (maximum).When approaching the outer range boundary, the Parent Unit may produce a scratching or interrupting sound.The system check function (lights 4, 15 and beeping sound on the Parent unit) will in principle indicate to you the reliability of the connection between the Parent unit and Baby unit and whether you are out of range. 12 ENGLISH SC484_book.qxd 23-09-2004 17:51 Pagina 12 SC484_book.qxd 23-09-2004 17:51 Pagina 13 ENGLISH 13 Problem solving If a fault occurs, first check the points listed below. If you are unable to remedy a problem by following these hints, contact the helpline or consult your dealer. Under no circumstances should you try to repair the set yourself as this will invalidate the guarantee. Problem Possible cause Solution DECT SYSTEM LINK light does not light Parent Unit: unit is not turned on. Baby Unit: unit is not turned on. Batteries are low. Power adapter is not plugged in or batteries are exhausted. Rechargeable batteries not inserted into Parent Unit. Press the Abutton (23). Press the Abutton (5) Replace/recharge batteries. Plug in power adapter or replace batteries. Place rechargeable batteries. High pitched noise Units are too close to each other. Volume too high. Move Parent Unit away from Baby Unit. Decrease the Parent Unit volume. Parent Unit batteries do not charge Battery life is at an end. Battery polarity misfitted. Poor contact between Unit and Charger. Replace rechargeable batteries, using only NiMH rechargeable batteries. Fit battery in correct polarity position. Clean Charger contact with soft dry cloth. No sound/ Cry of baby is not heard Volume on Parent Unit is set too low. Sensitivity setting on Parent Unit too low. Units are out of range. Increase Parent Unit volume. Adjust sensitivity level of Parent Unit. Move Parent Unit closer to Baby Unit. Parent unit reacts on other ambient sounds Ambient sounds other than the baby, trigger the transmission. Move the Baby Unit closer to the baby and try lowering the sensitivity on the Parent Unit. Battery check light lights (Baby Unit) or blinks (Parent Unit) Batteries are low or empty. Parent Unit: Baby Unit: Recharge or replace batteries. Replace or remove battery. DECT SYSTEM LINK light (flashing red)/ System check alarm beeps on Parent Unit Units too far away from each other. Batteries are low. Units cannot establish a connection, even whe...
Dieses Handbuch ist für folgende Modelle:Babyphone - SBCSC484/85 (5.58 mb)