Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Simply lift the Steam Mop Select off the floor. The flip mop head will spring forward. Place the edge of the mop head on the floor and apply forward or backward pressure depending on which side of the pad you wish to use. Flip mop pads Reusable microfiber mop pad is machine washable and safe for all hard floor surfaces. Your Steam Mop select may have come with two different pads. The all-white "soft" pad is best for everyday use on delicate flooring like sealed hardwoods and laminate. The gray and white striped pad can be used for scrubbing heavily soiled floors and tougher messes. Tip: Do not attempt to useyour Steam Mop Selectwithout water in the tank. 6 800.237.7691 Operations Operations Getting ready 1A 1B The mop pad may have alreadycome attached to the flip head, ifnot follow steps 1A and 1B below. 1. Attach mop pad A. Insert the flip head into the open end of the mop pad. B. Secure the Velcro flaps to ensure the pad is on tighty. 2. Fill the water tank A. Remove tank by lifting straight up and away from unit. B. Unscrew cap at bottom of water tank. C. Fill water tank with water. For best results, water should be at room temperature. d. Replace the cap, tighten until snug. E. Replace water tank by gently sliding tank into place. 3. Twist the quick release cord wrap clockwise to unwrap the power cord completely and plug into a 120-Volt outlet as described on the Important Safety Instructions, page 3. 4. The indicator light will illuminate when the Steam Mop Select is plugged in. 2A 2B 2d 2E Tip: Use of distilled water is recommended to prolong the life of your SteamMop Select 800.237.7691 7 Operations Operations Before you clean Thoroughly sweep or vacuum floor prior to cleaning with the Steam Mop Select. Cleaning hard floors Your Steam Mop Select is designed to clean hard flooring such as ceramic tile, vinyl, laminate, marble, stone and sealed hard wood floors. Use of your Steam Mop Select on waxed or some unwaxed floors may result in a diminished glossiness. The Steam Mop Select is not for use on unsealed wood floors. For best results test in an inconspicuous area and check the care instructions from your flooring manufacturer. 1. Plug the unit in and wait 30 seconds for it to heat up. Begin cleaning by slowly passing over surface while pressing the steam on demand trigger to emit steam as needed. 2. To sanitize an area of your floor, (attack invisible germs and bacteria) place the Steam Mop Select over the spot for a minimum 15 seconds using continuous steam, but no longer than 20 seconds using continuous steam. For larger areas, overlap swivel head placement. 3. When the mop pad becomes soiled, simply flip the mop head over to use the other side by lifting the Steam Mop Select off the floor. Lift the device off the floor so the flip head springs forward. Place the edge of the mop head on the floor and apply forward or backward pressure depending on which side of the pad you wish to use. NOTE: When cool, the mop head may not immediately spring for ward. While in use, the mop head will spring forward as directed. 4. When the Steam Mop Select stops emitting steam, unplug the unit. Simply remove the water tank, refill, and continue cleaning. WARNING: Never put descaling, alcoholic, or detergent products into the steam cleaner, as this may damage it or make it unsafe for use. Only use BISSELL authorized aromatic products 8 800.237.7691 Maintenance and care CAUTION: When you're done 1. Unplug power cord from outlet. Maintenance and care CAUTION: When you're done 1. Unplug power cord from outlet. 2. Carefully remove mop pad from flip head, as mop pad and lower assembly may be hot. 3. Any water remaining in the water tank should be emptied prior to machine storage. 4. Mop pad can be machine washed in warm water. Use only liquid detergents. Do not use fabric softeners. For best results, air dry. 5. Wrap power cord around quick release cord wrap on side of Steam Mop Select. 6. Wipe all surfaces of Steam Mop Select with a soft cloth. Store upright in a protected, dry area. Upright storage of theSteam Mop Select with awet mop pad may resultin the formation of white marks on your floor. Toremove the white marks, clean area with vinegar. 800.237.7691 9 Troubleshooting Reduced steam or no steam. possible Causes Remedies 1. Water tank empty 1. Fill tank Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSEll product. please do not return this product to the store. For any questions or concerns, BISSEll is happy to be of service. Contact us directly at 1-800-237-7691. Replacement parts- BISSELL Steam Mop™Select Item Part No. Part Name 1 203-7738 Handle Assembly 2 203-7734 Water Tank with Cap and Insert 3 203-7735 Cap and Insert Assembly 1 23 Additional Accessories Item Part No. Part Name 1 29H9-A Replacement Mop Pads - 2 pack 2 3252-1 Eucalyptus Mint Natural ...