Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: ATON Dateigröße: 382.94 kb Dateiname: Unterrichtssprache:

+ - + - + - + - A/V Receiver/Amplifier Figure 3.5 - Wiring: Amplifi er to Speaker-DVC • Use any of the wiring methods to connect to a mono speaker. This example shows a 2 conductor speaker wire running directly from the amplifier to the mono speaker. + - + - A/V Receiver/Amplifier Figure 3.6 - Wiring: Amplifi er to Speaker-Mono Note 1: Low voltage wiring must be run in accordance with the National Electrical Code as well as any other applicable provisions of the local building codes in your area. In some cases (such as commercial installations), running the wire in conduit may be required. If you have any questions concerning the wiring of speakers in your home, contact your local building and inspection department. Note 2: It is recommended that you use quality CL-2 or CL-3 rated stranded speaker wire when installing ATON speakers. Solid-core “Romex” type wire is not acceptable! Use at least 16AWG speaker wire for runs up to 100 feet, and at least 14 AWG speaker wire for runs up to 200 feet. If you must cross high-voltage lines, always do so at a 90 degree angle to avoid audible hum through the speakers!. Note 3: When pre-wiring for outdoor speakers, it is essential to make direct wire runs from the head-end to each speaker. Do not run speaker wires in series or parallel, and do not “daisy-chain” speakers to common wiring. There are instances where speakers will be connected directly to an amplifier. The use of spade lugs or bannana plugs is recommended in these instances. Page 4 ©2007 • All rights reserved. Storm Series Outdoor Speakers Mounting Use the included Mounting Brackets to securely mount the speakers in the desired location. To install the brackets on wood surfaces, vinyl siding, etc.: 1. Place brackets in desired location. 2. Mark location of holes at the narrow point of the keyhole cutout. 3. Drill pilot holes.. 4. Partially tighten screws. 5. Place the brackets in position, then tighten the screws. Screw Location Figure 3.7 - Screw Location To install the brackets on brick or concrete surfaces: 1. Place brackets in desired location 2. Mark location of holes at the narrow point of the keyhole cutout 3. Drill holes using a masonry drill bit. 4. Insert masonry anchors into the holes previously drilled 5. Tighten screws partway into the anchors 6. Mount the brackets then tighten screws To install the brackets on drywall: 1. Place brackets in desired location Brick/Concrete Masonry Anchor Screw Figure 3.8 - Brick/Concrete 2. Mark location of holes at the narrow point of the keyhole cutout 3. Drill holes using a drill bit. 4. Insert drywall anchors into the holes previously drilled 5. Tighten screws partway into the anchors 6. Mount the brackets then tighten screws Drywall Drywall Anchor Screw Figure 3.9 - Drywall © 2007 • All rights reserved. Page 5 Storm Series Outdoor Speakers Once the brackets are mounted, place the speakers between each end of the bracket. Install a Bracket Knob on each end of the speaker as shown in Figure 3.10. Adjust the speaker to the desired location, and firmly tighten the Bracket Knob. Mounting Bracket Screws Bracket Knob Bracket Knob Figure 3.10 - Mounting Speaker to Bracket Connection Once the speakers are mounted, they can be connected to the wires previously installed. Cut the ends of the wire to length, allowing some free play (about 6 inches of slack) to allow for moving the speakers and physically connecting them to the wire. Using wire strippers, remove 1/2 inch of insulation, then twist the wire to ensure that no stray strands are evident. Define positive (+) and negative (-) at the amplifier end and the speaker end of the wire run and use the same conductor on each end. Several Connection methods are possible: 1. Bare wire - Loosen the binding post of the speaker and insert bare wires into the holes on the side of the connector; + to + (red) and - to - (black). Tighten the binding post to make sure the wires are fi rmly connected. 2. Bannana Plugs - Terminate the speaker wires with Bannana plugs, loosen the bind- ing posts, then insert the plugs into the center holes; + to + (red) and - to - (black). Tighten the bi...

Herunterladen

Geben Sie zwei Ziffern: