Stimmen - 5, Durchschnittliche Bewertung: 3.4 ( )

Hersteller: Air King Dateigröße: 117.64 kb Dateiname: 6fa46c8a-08e3-484c-a0f9-2626b3764873.pdf Unterrichtssprache:

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSON, OBSERVE THE FOLLOWING: 1. Read all instructions before installing or using the central vacuum. 2. Use this central vacuum only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. WARNING: DO NOT DEPEND UPON THE UNIT’S CONTROLS AS THE SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING. ALWAYS UNPLUG THE UNIT. 3. Before servicing or cleaning the unit, unplug the unit. 4. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire- related construction. 5. Make certain that the power source conforms to the electrical requirements of the unit. CAUTION: THIS UNIT MUST NOT BE USED IN POTENTIALLY DANGEROUS LOCATIONS SUCH AS FLAMMABLE, EXPLOSIVE, CHEMICALLADEN OR WET ATMOSPHERES. 6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. CAUTION: EXHAUST SHOULD NOT BE VENTED INTO A WALL, CEILING, OR CONCEALED SPACE WITHIN THE HOME. 7. This unit is not intended for use on wet or outdoor locations, flammable or combustible liquids, burning or smoking items such as cigarettes, matches, or hot ashes. 8. The central vacuum must be grounded as a precaution against possible electrical shock. 9. Do not use with damaged cord or plug. 10. Do not insert any objects into openings other than acceptable hose connections. 11. Use extra care when vacuuming on stairs. 12. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. ELECTRICAL REQUIREMENTS WARNING:IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING CONDUCTOR CAN RESULT IS A RISK OF ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE UNIT- IF IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN. WARNING: THIS UNIT IS FOR USE ON A NOMINAL 120 VOLT CIRCUIT AND HAS A GROUNDING PLUG. MAKE SURE THAT THE UNIT IS CONNECTED TO AN OUTLET HAVING THE SAME CONFIGURATIONS AS THE PLUG. NO ADAPTER SHOULD BE USED WITH THIS UNIT. This unit requires a dedicated, grounded electrical outlet of 120 volts AC, 60 Hz, 15 amp circuit. SAVE THESE INSTRUCTIONS 000000 Rev A. 3-05 1 of 16 INSTALLATION INSTRUCTIONS 1. Unpack central vacuum power unit from the carton and confirm that all pieces are present. In addition to the power unit you should have: 1 - Power unit mounting bracket 1 - Inlet valve 1 - Instruction/Safety Sheet Planning the Installation The Air King Central Vacuum System consists of three major components. The power unit, fittings including the inlet valves and tubing, and the tool kit. The power unit is designed to be permanently mounted in one location with connections made to the living area with a network of inlets and tubing. Locating the Power Unit 1. The power unit can be located in a garage, basement, utility room, or any other room that allows for sufficient ventilation, is dry, and provides accessibility to the unit for emptying the collection canister. CAUTION: IF THE POWER UNIT IS INSTALLED IN A CLOSET OR UTILITY ROOM, IT MUST BE VENTED TO PROVIDE ENOUGH AIR FLOW. LOUVERED DOORS CAN BE USED. DO NOT MOUNT IN A HIGH AMBIENT TEMPERATURE AREA SUCH AS ATTIC, FURNACE ROOM, ETC. NOTE: If venting the unit to the outdoors, avoid venting to areas such as patios or entranceways. 2. The power unit should be mounted within 5 feet of an acceptable outlet. Check the electrical specifications of your specific unit to ensure the circuit is not being overloaded. A dedicated 15 amp circuit should be used. Locating the Inlet Valves 1. The number of inlet valves will be determined by the layout of your home. The hose must be able to reach every corner of the home including inside closets and around furniture. Inlets should be placed in central locations and avoid placing behind furniture or doors. 2. Using a 30 foot piece of string or the hose itself, have one person hold one end to the planned inlet location and have the second person walk around the room(s) to determine if more inlets are needed. Continue this exercise until you can reach every area of the home (Figure 1). Figure 1 Living Room Bedrm Garage Kitchen Hall Power Unit Bath Bedrm Bedrm 3. If the installation is for new constructions and you are worki...

Herunterladen

Geben Sie zwei Ziffern: