Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
The R-4 communicates with a NetLinx master via a wireless ZigBee® network: the device comes with installed firmware for connecting to a ZigBee Pro network, but it can be updated with firmware to allow it to connect to older ZigBee networks. Use TPDesign4 (TPD4) to program this device. The R-4 uses a mini-USB port for transferring programming files. Touch Screen FIG. 1 Mio Modero R-4 Remote 1 2 3 4 5 6 7 8 910 19 11 12 1315 14 16 17 18 20 1 - Power 2 - Guide 3 - Exit 4 - Menu 5 - Information 6 - Move Up 7 - Move Down 8 - Move Left 9 - Move Right 10 - Select 11 - Volume Up 12 - Volume Down 13 - Channel Up 14 - Channel Down 15 - Last Viewed 16 - Mute 17 - Input 18 - Enter 19 - Back/Home 20 - Up/Down Touch Screen Navigation Numeral Keypad Touch And Tilt Sensor The Mio R-4 wakes up upon touching either the chrome side rails or pressing a button. If the remote goes to sleep when holding it, you can reawaken the device by tilting it. Errant jostling, such as bumping a table on which the device rests, will not wake the device unless you are holding it. Specifications Mio R-4 (FG148-04) Specifications Battery Rechargeable Lithium-Ion Transmission Frequencies • ZigBee RF wireless network Transmission Range • 100 feet (30.48m). Memory • 32 Mbytes of FLASH • 64 Mbytes of SDRAM Top Components • LED - blue backlit buttons indicate device is awake • LCD - high resolution (240x320) 76800 pixels with backlight and touch overlay • Pushbuttons - the power button is red backlit; the rest are blue backlit buttons. 29 buttons total Mio R-4 (FG148-04) Specifications (Cont.) Rear Components • Programming Port • Battery Door • Rechargeable Battery Connection Dimensions (HWD) 9.50 x 2.00 x .74 (241.3 mm x 50.8 mm x 18.80 mm) Supported Languages: • English •Spanish • French • Italian • German • Portuguese • Arabic • Russian • Greek • Simplified Chinese • Japanese • Thai • Hindi • Korean Certifications: • FCC ID: CWU-NXR-MO • IC: 5078A-NXRMO •CE • IEC-60950 • Japan Approval • Designed for ZigBee Weight • .45 lbs (20 g) without batteries • .55 lbs (25 g) with batteries Operating Environment • Operating Temperature: 0° to 40° C (32° to 104° F) • Storage Temperature: -20° to 70° C (-4° to 158° F) Included Items • Mio-RBP Rechargeable Lithium-ion Battery (FG147-10) Optional Keypads: • MIO-R4-KP-ITALIAN (FG148-141) • MIO-R4-KP-FRENCH (FG148-142) • MIO-R4-KP-ARABIC (FG148-143) • MIO-R4-KP-CHINESE (FG148-144) Other AMX Equipment • CC-USB Programming cable (FG10-5965) • Mio-RCC Charging Base (FG147-02) with power supply • NXR-ZGW (FG5791-01) • NXR-ZRP-PRO (FG5791-03) Inserting the Lithium-Ion Battery Into The Mio R-4 To install your Lithium-Ion battery into the Mio R-4: 1. Flip and turn the Mio R-4 so that the buttons are facing away from you and the device is upside down. 2. Holding the device in both hands, place your thumbs on the battery door and slide the battery door free. 3. Connect the terminal end of the Lithium-Ion battery to the port shown in FIG. 2. It may be necessary to use a thin, blunt non-conductive object to seat the battery connector fully within its port. (Note: Make sure that the battery wires run alongside the battery in the compartment as shown in FIG. 2. Otherwise, the wires may be damaged or the battery door may not close properly.) 4. Replace the battery door, and slide it to lock it in place. Programming Port Rear view (USB) battery compartment Lithium-Ion Battery Correct path for battery wires and connector Rechargeable Battery Port Connection FIG. 2 Rechargeable Battery and Programming Ports on The Mio R-4 Remote Installing a Supported Language Keypad 1. Remove the battery door (See Inserting the Lithium-Ion Battery Into the Mio R-4) and remove the battery. 2. Unscrew the 6 screw points. 3. Turn the unit over so the buttons are facing you. 4. Lift the top assembly away from the PCB. 5. If necessary, push out the standard buttons from the front of the top assembly. 6. Drop in your language pad and verify the alignment with the guide posts on the PCB. 7. Place the top assembly back down on the PCB and return the unit over, exposing the 6 screw points. 8. Tighten the 6 screw points. 9. Reinstall the battery, replace the battery door, and slide the door to lock it in place. Using the Programming Jack on the Mio R-4 The programming jack located on the back of the Mio R-4 (FIG. 2) is used for communication between the device and TPDesign4. The programming jack uses a CC-USB Programming cable, USB to mini USB (FG10-5965). You can order the programming cable from AMX if you do not have one. While loading your configuration file, make sure the device is situated in the charging cradle. 1. Remove the battery door (See Inserting the Lithium-Ion Battery Into the Mio R-4). 2. Connect the mini USB programming cable (FG10-5965) into the programming jack. 3. Connect the other end of the USB cable to the USB port on your computer. 4. Configure the communication parameters in TPDesign4. For more information, please refer to the Mio...