Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV,VCR and DVD. On our website you can directly select your device typenumber to find the right code. Make sure you use the codes from the correct table. 3 Press the TV key to select TV. Press the key until it lights up. 4 Keep keys 1 and 3 pressed simultaneously for three seconds until the TV key flashes twice and then remains lit. 5 Then enter the code noted in step 2 using the digit keys. – The TV key will now flash twice. If the key flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Start again from step 2. 6 Point the SRU520 at the TV and check that it responds as it should. – If the TV responds to all of the key commands, the SRU520 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. 6 Instructions for use English SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 6 Instructions for use 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. 1 y Standby . . . . . . . . switches TV,VCR or DVD on or off. 2 . . . - teletext on/off ( ); . . . - text mix ( ); . . . - text off ( ); -wide screen TV ( ); -enlarge ( ); -text hold ( ). 3 MENU . . . . . . . . . . . turns the menu on and off. 4 Cursor keys . . . . . . cursor up, down, left, right in a menu. 5 A/V. . . . . . . . . . . . . . . . switches between external inputs of your equipment. 6 s . . . . . . . . . . . . . . . . mutes the sound of the TV. 7 - VOL +. . . . . . . . . . . adjusts the TV volume. 8 Digit keys . . . . . . . . direct choice of channels and other functions. 9 SHIFT . . . . . . . . . . . for extra functions. When pressed at the same time as a second key, the second key will get another function. All blue labelled keys can be used together with SHIFT. For example: SHIFT + INSTALLinstalls your TV SHIFT + STORE. . stores TV settings Try out other combinations with the SHIFT-key on your device in order to find out which functions are available. Only functions featured on the original remote control are available. 0 5. . . . . . . . . . . . . . . . - red teletext key -rewind (VCR/DVD) 2 . . . . . . . . . . . . . . . . - index -play (VCR/DVD) 6. . . . . . . . . . . . . . . . - blue teletext key -wind (VCR/DVD) 9 . . . . . . . . . . . . . . . . - green teletext key -stop (VCR/DVD) 0 . . . . . . . . . . . . . . . . record ;. . . . . . . . . . . . . . . . . - yellow teletext key -pause (VCR/DVD) ! / . . . . . . . . . . . . . . . selects between one- and two-figure channel numbers. @ 2 22 . . . . . . . . . . . . . . . selects previous programme/channel. # - PROG + . . . . . . . . selects a previous or following channel. $ OK. . . . . . . . . . . . . . . confirms your selection. % BACK . . . . . . . . . . . . jumps back one level in the menu or turns off the menu. ^ TV - DVD/VCR . . . seletcs TV or DVD/VCR mode. If you use the (fi) 'memory off' key to get to the next teletext page on your Philips TV, you can press the STOP key for this. See also ‘Troubleshooting’. • If the device does not respond at all, or not to all of the key commands, follow the instructions under ‘Setting the remote control’. It is possible that you must enter another code for the device. English 7 Instructions for use English 4. Extra possibilities Adjusting device selection (Mode keys) The SRU520 is default set for operating TV, VCR or DVD. You can select the device you wish to operate with TV and DVD/VCR selection buttons. Each key allows operation of one device only. If desired, you can program the keys to select a different kind of device. For example, if you want to operate a second TV. In the following example you will see how to configure the VCR/DVD key for a second TV. 1 Switch on the second TV. 2 Press the DVD/VCR key to select DVD/VCR. Press the key until the it lights up. 3 Then keep keys 1 and 6 on the SRU520 pressed simultaneously for three seconds, until the VCR/DVD key lights up. 4 Press keys 9, 9 and 2, in that order. 5 Press the TV key to select TV. Press the key until it lights up. 6 – Press the 1 key. The VCR/DVD key flashes twice. The VCR/DVD key will now allow you to operate your second TV. 7 Program the SRU520 to operate the second TV. See ‘Setting the remote control’. Adding a function to the remote control If you want to add a function to the SRU520, you can contact the Philips ser vice line for Universal Remote Control to ask for the 5-figure code for the extra function. 8 Instructions for use Restoring the original functions of your remote control English 1 Keep keys 1 and 6 on the SRU520 pressed simultaneously for three seconds, until the mode key (TV or DVD/VCR) flashes twice and then rem...