Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 304.49 kb Dateiname: Unterrichtssprache:

Reproduction in whole or in part is prohibited without prior consent of the copyright owner. Philips Innovative Applications N.V. is not liable for omissions or for technical or editorial errors in this manual or for damages directly or indirectly resulting from the use of the RFX9200. The information in this user guide may be subject to change without prior notice. All brand or product names are trademarks or registered trademarks of their respective companies or organizations. Concept and realisation of the Guide: Human Interface Group, De Regenboog 11, 2800 Mechelen (Belgium) Contents 1 How to Use the Extender 4 1.1 Introduction 4 ENGLISH 1.2 Taking a Closer Look 6 2 How to Install the Extender 7 2.1 How to Configure the Extender 7 2.2 How to Connect the Extender 7 2.3 How to Position the Extender when Using the Front Blaster 7 2.4 How to Install the Single IR Emitters 9 3 How to Do More 10 3.1 How to Set the Extender IDs 10 3.2 How to Do a Range Check 12 3.3 How to Avoid Interference from Other Remote Controls 11 3.4 How to Adjust the Power Level of the IR Outputs 12 4 Troubleshooting 12 5 Specifications 13 Approbation & safety content RFX9200 14 FCC Compliancy 14 CE Regulations According to R&TTE 15 WEEE regulation (for EU only): 16 Contents 3 How to Use the Extender 1.1 Introduction Infrared (IR) remote controls do not work properly when obstacles between the remote control and the audio/video devices disturb the operating signal. This problem can be solved using radio frequency (RF) as a carrier for IR commands. The Remote Control, in combination with the Extender, can operate audio/video devices from virtually any location. A/VequipmentRemoteControlExtenderPCX9200MediaCenter When the front blaster of the Extender cannot reach all devices or transmits with too much power, you can use the included Single IR emitters. You can set up the Single IR emitters in two ways: • The Single IR emitters in combination with the front blaster. When there is limited space around the IR receivers of the devices, for instance in a small closet. • The Single IR emitters instead of the front blaster. When you want to transmit IR signals very accurately, you turn off the front blaster and control the devices by using the Single IR emitters alone. How to Use the Extender ENGLISH You can combine multiple extenders or combine the RFX9200 and the PCX9200 as shown in the situation above. You can control each Extender individually with one or more Remote Controls. How to Use the Extender 5 1.1 Taking a Closer Look PowerledFrontblasterBusyledChannelswitch Extender ID dial Power input 4 IR outputs 4 dipswitches for IR outputs How to Use the Extender How to Install the Extender Make sure you have the following components: Extender, power adapter, Single IR emitters and optionally screws. The installation of the Extender consists of 4 main steps: • Configuring the Extender; • Connecting the Extender; • Positioning the Extender; • Installing the Single IR emitters. 2.1 How to Configure the Extender In the Link Extenders to components step of the New Project Wizard of the Configuration Program: • Define the channel; • Add Extender 0 to the project; • Link the components to the Extender; • Define which IR port to use: the front blaster or one of the 4 other IR ports. E Tip To add more than one Extender to the project, see How to Do More on page 10. Plug the power cable into the back of the Extender. Plug the power adapter into the mains wall socket. When connected, the Power LED on the Extender will light up. 2.2 How to Connect the Extender 1 2 2.3 How to Position the Extender when Using the Front Blaster For optimal results, the Extender should be positioned horizontally, either facing up or facing down. Make sure to place the Extender in a central position aimed directly at the A/V devices. The front blaster (the front part of the dark plastic window on top of the Extender) in particular should be aimed at the devices, since the IR signals sent out by the IR blaster must reach the IR receivers of the devices. For optimal IR reception, position the Extender so the devices are located within its working range, as shown in the picture below. ENGLISH How to Install the Extender 7 Reflection area Once you have found the best position, you can optionally mount the Extender onto a piece of furniture using screws. 1 Drive the screws into a rack, closet or another piece of furniture. Provide sufficient space to connect the power adapter and to slide the Extender in place. E Tip Depending on the surface, it may be possible to attach the Extender to the furniture using a piece of 2-sided tape or velcro. 2 Slide the Extender in place. How to Install the Extender 2.4 How to Install the Single IR Emitters The Single IR emitters can be used in combination with, or as an alternative to the front blaster. Plug the Single IR emitters into the Extender. Attach the Single IR emitters to a neighboring surface facing the IR receiver (for...

Herunterladen

Geben Sie zwei Ziffern: