Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
No transport keys except the STOP key will have any function at this time. The start of the program material should follow closely after the controller display reaches "XX 01 0000". After 10 seconds, the REC and PLAY lights go out, and a "STOP" command is sent from the REMOTE and the PARALLEL I/O connectors. Re-locate the source to the start (adjusting the locate point if necessary). Further rehearsals can be carried out as long as the REHEARSAL indicator and the STDBY key are both lit. Levels Make sure that the loudest part of the program material lights the "0" segment of the controller's meters, but does not light the "OVER" segment. This does not have to be done in rehearsal mode, but should be done before a recording on disc is made, to avoid digital clipping. To turn off the rehearsal mode, press the REHEARSAL key so that the indicator goes out. 6.2.4 Audio recording NOTE: Recording can only take place when the STDBY key is lit steadily (not flashing). Make sure the source is located to the required position. Press the REC and PLAY keys together. Both will light steadily. If the source is being controlled by the REMOTE or PARALLEL I/O signals, the "PLAY" command (REMOTE) will be sent at the -01 second, 74 frames point. "PLAY1" and "PLAY2" messages will be sent from the PARALLEL I/O connector. See the "Parallel I/O timing chart" on page 35 for details. If the source is being manually controlled, start the source as soon as the display on the controller reaches "XX 01 0000". With the LINE indicator illuminated, monitoring can be done from the source (INPUT) or off-disc (REPRO) by selecting the appropriate option. As the recording progresses, the rightmost indicators (time indicators) of the display will advance. If the program is longer than the pre-defined track length, the track number will be incremented automatically. It is not possible to use the TrINC (track increment) key in TOC PRE mode, but the IxINC (index incre- YPDR Operation - 24 6 • Operation - Recording variable tracks (TOC AFTER mode) ment) key can be used to write index markers after the index number in the display has changed to "01". REC MUTE The REC MUTE key will mute the signal from the source while recording is m progress. The REC MUTE key is latching (press once for on, again for off). The input can be monitored during muting by setting the IN PUT/RE PRO key to INPUT. STOP/PAUSE If the STOP or PAUSE key is pressed more than one second before the end of the current track, the record mute function is enabled, the display will flash, and the YPDR will record silence until the end of the current track. If STOP has been pressed, the YPDR will go into stop mode (STOP will be lit). If PAUSE has been pressed, the YPDR will go into record pause mode (REC and PAUSE will be lit). Pressing the STOP key or the PAUSE key will also send a remote "STOP" message. NOTE: PAUSE and STOP operations as described above will not work while recording track 99. However, a remote "STOP" message will be transmitted. To restart recording from PAUSE, press PLAY alone (the REC key will remain lit). To restart recording from STOP, enter standby mode, and press PLAY and REC together. AUTO PAUSE When the AUTO PAUSE key is on, recording will automatically pause at the end of each track (10 or 30 seconds), and the YPDR will go into PAUSE mode. The AUTO PAUSE key can be turned on or off in standby, record, or record pause mode. The STOP and REC MUTE keys can also be used when the AUTO PAUSE key is lit, as described above. NOTE: A disc recorded in the TOC PRE mode can be played on any CD player, even if only a few tracks out of the 99 available tracks have been recorded. However, some players may experience difficulties when set to repeat the last track. This can be overcome by recording a blank track immediately following the last recorded track. 6.2.5 Lead-out To complete a CD capable of being played on an ordinary CD player, a "lead-out" should be recorded. This is done automatically after the last track (track 99 in TOC PRE mode). After the last program material has been recorded, start recording from standby mode (REC and PLAY simultaneously). Recording will continue up to the 99th track, and then the lead-out will be recorded. While this is taking place, any source material input will be recorded. Make sure REC MUTE is on to avoid recording unwanted material. 6.3 Recording variable tracks (TOC AFTER mode) Recording in the TOC AFTER mode allows a variable number of tracks to be recorded, of different lengths. However, a disc produced in this way cannot be read on a commercial CD player until the final TOC has been written (though it can be replayed on the YPDR). YPDR Operation - 25 6 • Operation - Recording variable tracks (TOC AFTER mode) When a blank disc is inserted, the display will show "OOOObd". If a disc already containing audio data but no TOC data is inserted, the display will show "xxOOAd", where "xx" is equal to the...
Dieses Handbuch ist für folgende Modelle:Player - YPDR601 (2.78 mb)