These instructions are not intended to be comprehensive. Please consult the Keypad Programming Manual for complete information. © 2005 The Chamberlain Group, Inc. All Rights Reserved Guide for Programming the EL25 ProgrammingNumber Description of T ask Factor ySetting Programming Procedure *** Entering Programming Mode *** (6 Digit Password) 0 Exiting Programming Mode 0 # 1 Change or Verify the Unit's Password 000000 1 # (1 to change; 2 to verify) # (six-digit code) # 2 Set Unit ID Number and No

MONITOR HOLD OFF 1 3 2 4 VOLUME TALK ACTIVE Program Additional Intercoms 1 2 Troubleshooting Intercom does not function. Check batteries in intercom. If using a DC Adapter ensure that it is plugged in. Ensure intercom is connected to a network. See Program. Ensure that intercoms are on the same channel. See Operation. The intercom can be programmed to at least one other intercom to become a network or it can be programmed into an existing network. CREATE NEW NETWORK Before programming, clear mem

The intercom is compatible with various Chamberlain Wireless Products. Features On/Off: To turn intercom ON, press Talk button. To turn intercom OFF, hold down the Volume DOWN button for 3 seconds. Talk Button: Following the ringing of the doorbell by a guest, press and hold the Talk button to talk to the guest. Once the link to the doorbell is made, any other intercoms in the network cannot hear the conversation. Volume: Pressing the Volume DOWN button will lower the volume and pressing the Vol

All intercoms must be set to the same channel or the paging channel to be in Conference Mode. To put intercom in Conference Mode set Dipswitch #2 to UP position. Monitor Mode: Monitor Mode is used to monitor the noise in a specifi c room. Place the intercom in the room that is to be monitored and press the Monitor button until a tone is heard. For extended Monitor usage, consider using a plug-in transformer. Any other networked intercom can listen to that room. If a specifi c channel is selected

A cordless phone, cell phone, or other radio devices can also cause static. The intercom does not connect to another intercom and a green light is on longer than 3-1/2 minutes. The intercom is out of range. Place the intercom closer to the other intercoms in the network, with the antenna pointing up. The other intercom in the network has no power. Replace the batteries. The intercom has not completed programming. Clear the intercom's memory and reprogram. Need to clear intercom’s memory. Press a

Volume: Pressing the Volume DOWN button will lower the volume and pressing the Volume UP button will increase the volume. Intercom Models NLS1 & NLS1C (1) NLS2 & NLS2C (2) Rubber Pads Models NLS1 & NLS1C (1) NLS2 & NLS2C (2) MONITOR HOLD OFF 1 3 2 4 VOLUME TAL K ACTIVE Operation & Features Channel Select Button: Press the Channel Select button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel li

Create New Network Before programming, clear memory on all intercoms. Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put the second intercom into Learn Mode (refer to the following table). Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. Repeat for any additional intercoms. Add to an Existing Network Press the Learn button on the new intercom until a beep is heard. Within 10

Each application is unique, it is the responsibility of the purchasers, designer, installer and end user to ensure that the total control access system is safe for its intended use. Please refer to the manuals and/or qualified technician for further information. NOTE: The default password is “Manager.” 1. Click the NEW UNIT ICON Enter Unit Name and Unit Type 1 Enter Country, State/Prov. and City 2 Click OK3 2. Click the Unit Configuration ICON and Select the CONTROL SETTINGS Tab 21Uncheck the “U

The Wireless Gate Access Intercom is compatible with various Chamberlain Wireless Products and all Chamberlain Gate Operators. Indoor Intercom Rubber Pads Operation & Features Talk Button: Following the ringing of the doorbell by a guest, press and hold the Talk button to talk to the guest. Once the link to the Outdoor Intercom is made, any other intercoms in the network cannot hear the conversation. Select Button: During a conversation, the Select button can be pressed to open the gate. A beep

The MUGAPLM is compatible with various LiftMaster Wireless Products. Multi-Unit Gate Access Panel (MUGAPLM) Bolt (4) Washer (4) Nut (4)Key (2) Telephone Interface Unit (OTIU): The OTIU allows the user to identify which gate or door a visitor is at with Caller ID and a distinctive ring tone. To answer a call press “0”. A gate can be opened by dialing “*9” on the telephone keypad. Accessory Overview Portable Intercom: The intercom allows the user to speak with visitors at the MUGAPLM and open the