Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Hold the camcorder in the desired position and tilt the LCD monitor in the most convenient direction. It can rotate 270° (90° downward, 180° upward). SELF-RECORDING You can shoot yourself while viewing your own image in the LCD monitor. Open the LCD monitor and tilt it upward 180° so that it faces forward, then point the lens toward yourself and start recording. Operation Mode Choose the appropriate operation mode according to your preference using the Power Switch. To turn on the camcorder, set the Power Switch to any operation mode except “OFF”while pressing down the Lock Button located on the switch. Power Switch Position (Manual): Allows you to set various recording functions using the Menus. If you want more creative capabilities than Full Auto recording, try this mode. (Full Auto): Allows you to record using NO special effects or manual adjustments. Suitable for standard recording. OFF: Allows you to switch off the camcorder. PLAY: • Allows you to play back a recording on the tape. • Allows you to transfer a still image recorded on the tape to a computer. PLAYOFF Power Switch Lock Button When the Power Switch is set to “ ”, “ ” appears. When set to “ ” or “PLAY”, there is no indication. Power lamp Self- Recording EN 17 FEATURE: Zooming 1x W T 01x W T 02x W T 04x W T Zoom in (T: Telephoto) Zoom out (W: Wide angle) Zoom display 6 1xW T Digital zoom zone 16X (optical) zoom zone Approximate zoom ratio Power Zoom Lever PURPOSE: To produce the zoom in/out effect, or an instantaneous change in image magnification. OPERATION: Zoom In Slide the Power Zoom Lever towards “T”. Zoom Out Slide the Power Zoom Lever towards “W”. . The further you slide the Power Zoom Lever, the quicker the zoom action. NOTES: . Focusing may become unstable during Zooming. In this case, set the zoom while in Record-Standby, lock the focus by using the manual focus ( pg. 29), then zoom in or out in Record mode. . Zooming is possible to a maximum of 700X, or it can be switched to 16X magnification using the optical zoom ( pg. 33). . Zoom magnification of over 16X is done through Digital image processing, and is therefore called Digital Zoom. . During Digital zoom, the quality of image may suffer. . Macro shooting (as close as approx. 5 cm to the subject) is possible when the Power Zoom Lever is set all the way to “W”. Also see “TELE MACRO” in the Menu Screen on page 34. 18 EN RECORDING (cont.) Time Code During recording, a time code is recorded on the tape. This code is to confirm the location of the recorded scene on the tape during playback. If recording starts from a blank portion, the time code begins counting from “00:00:00” (minute:second:frame). If recording starts from the end of a previously recorded scene, the time code continues from the last time code number. If during recording a blank portion is left partway through the tape, the time code is interrupted. When recording is resumed, the time code starts counting up again from “00:00:00”. This means the camcorder may record the same time codes as those existing in a previously recorded scene. To prevent this, perform “Recording From The Middle of A Tape” below in the following cases; • When shooting again after playing back a recorded tape. • When power shuts off during shooting. • When a tape is removed and re-inserted during shooting. • When shooting using a partially recorded tape. • When shooting on a blank portion located partway through the tape. • When shooting again after shooting a scene then opening/closing the cassette holder cover. Recording From The Middle Of A Tape Display Frames are not displayed during recording. Minutes Seconds Frames (25 frames = 1 second) 12 : 34 : 24 1. Play back a tape or use Blank Search ( pg. 22) to find the spot at which you want to start recording, then engage the Still Playback mode ( pg. 19). 2. Set the Power Switch to “ ” or “ ” while pressing down the Lock Button located on the switch, then start recording. NOTES: . The time code cannot be reset. . During fast-forwarding and rewinding, the time code indication does not move smoothly. . The time code is displayed only when “TIME CODE” is set to “ON” ( pg. 35, 37). When a blank portion is recorded on a tape Time code 00:00:00 Tape Shooting start point Proper recording Time code 00:00:00 Tape Shooting start point Time code 05:43:21 Newly recorded sceneBlankAlready recorded scene Shooting stop point Time code 05:43:21 Latest sceneNew sceneAlready recorded scene Shooting start point Time code 00:00:00 Shooting start point Time code 05:44:00 Shooting start point PLAYBACK EN 19 Normal Playback 1 Load a tape ( pg. 12). 2 Set the Power Switch to “PLAY” while pressing down the Lock Button located on the switch. To start playback, press 4/6. • To stop playback, press 5. • Press 2 to rewind, or 3 to fast-forward the tape during Stop mode. To Control The Speaker Volume . . . ..... slide the Power Zoom Lever (VOL.) towards “+” to turn up the volume, or towards “–” to turn down the volume. NOTE...