Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
If you don’t have a modular jack, call your local phone company to find out how to get one installed. POWERING THE CALLER ID UNIT INSTALLING THE BATTERIES Disconnect the line cords from the back of the unit and wait a few seconds for the unit to go into standby. 1. Use a screwdriver or other flat tool to open the battery compartment door. 2. Insert 3 "AAA" size batteries as shown on the diagram in the battery compartment. 3. Close the battery compartment door securely. LOW BATTERY INDICATOR If the low battery icon appears in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible in order to retain the information in the Caller ID memory. INSTALLATION IMPORTANT INSTALLATION INFORMATION • Never install telephone wiring during a lightning storm. • Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. INSTALLING YOUR CALLER ID 1. Connect the telephone line cord to either jack on the back of the unit and to the modular jack on the wall. 2. Connect your phone’s line cord to the jack on the back of the unit. ANSWERING MACHINE INSTALLATION The answering machine must be set to answer calls after at least 2 rings to properly receive Caller ID information. To use your Caller ID unit with an answering machine: 1. Plug a telephone line cord into the modular jack and the Caller ID unit. 2. Plug another telephone line cord into the other phone jack on the Caller ID unit and into the answering machine. 3. Plug a third telephone line cord into the answering machine and into the phone. TWO-LINE SYSTEM INSTALLATION You must use two Caller ID units if you want to use Caller ID for both lines. You must also purchase a triplex adapter. 1. Plug the triplex adapter into your two- line modular wall jack. 2. Plug your two-line phone into the two-line receptacle on the triplex adapter. 3. Plug each Caller ID unit into a single- line receptacle on the triplex adapter. CALLER CALLER LCD DISPLAY REVIEW DELETE LCD DISPLAY REVIEW DELETE OPERATION CHOOSING A LANGUAGE This unit can display the message indicators in English, Spanish, or French. When you set up your Caller ID unit ENGLISH appears in the display. To select the language: 1. Press REVIEW until you reach the desired language. 2. Press DELETE to select the language. To change your language selection after initial setup, you must power down the unit and follow the steps above. To power down the unit: 1. Remove batteries, wait 15 minutes and replace the batteries. RECEIVING AND STORING CALLS This unit receives and displays information transmitted by your local phone company. This information can include the phone number, date, and time; or the name, phone number, date, and time. The unit can store up to 30 calls for later review. When the memory is full, a new call automatically replaces the oldest call in memory. NOTE: Check with your local phone company regarding name service availability. DELETE AND REVIEW BUTTONS DELETE BUTTON • To delete the record shown in the display, press the DELETE button. • To delete all records, press and hold the DELETE button for about 5 seconds (until NO CALLappears in the display). REVIEW BUTTONS • Press REVIEW to see the next record. When all messages have been viewed, END OF LIST appears in the display. • Press REVIEW to view previous records. DISPLAY CONTRAST ADJUSTMENT DELETE REVIEW To adjust the contrast on the display: button button • Note: To scroll through records, press and hold REVIEW or REVIEWNote: To scroll through the contrast settings, press and hold both REVIEW buttons. Press and hold REVIEW while you press and REVIEWDELETE M # NEW A CALL LOW REVIEW release REVIEW . button • Release both buttons when the contrast is set to desired level. MESSAGE INDICATORS The following special messages indicate the status of a message or the unit: NO CALL The caller memory is empty. OUT OF AREA The incoming call does not have Caller ID service or their service area is not linked to yours. Low battery icon Battery power level is low. PRIVATE CALL The caller of the incoming call is registered as “Private Number” and their Caller ID information is withheld. ERROR Caller information has been interrupted during transmission. END OF LIST There are no additional calls to review. TROUBLESHOOTING TIPS NO DIAL TONE ON THE PHONE ATTACHED TO THE CALLER ID UNIT • Check all cabling to make sure that all connections are secure. NO DISPLAY • Replace batteries. • Did you order Caller ID service from your local telephone company? This unit requires that you subscribe to Caller ID service in order to work. ERROR MESSAGE IS DISPLAYED • ERRORappears in the display if the unit detects anything other than valid Caller ID information during the silent period after the first ring. This message indicates either the presence of noise on the line, or that an invalid message has been sent ...
Dieses Handbuch ist für folgende Modelle:Telefonanlagen - 347A8203-0001 (70.99 kb)