Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Westinghouse Dateigröße: 1.68 mb Dateiname: Unterrichtssprache:

SPEAK TOWARDS THE CONSOLE RELEASE THE ALL CALL BUTTON WHEN YOU ARE FINISHED TALKING NOTE: ANY CONSOLE WITH ITS MUTE SWITCH ON AND ANY DOORBELL UNITS THAT HAVE NOT BEEN USED IN THE PRIOR 60 SECONDS WILL NOT RECEIVE THE ALL-CALL MESSAGE EXAMPLE: KITCHEN IS CALLING EVERYONE ALL STATION INDICATORS LIGHT KITCHEN CALLS ALL STATIONS KITCHEN CONSOLE 2 WAIT FOR RESPONSE ALL CONSOLES THAT RECEIVED THE ALL-CALL MESSAGE WILL SOUND THE MESSAGE THE CALLER THEN WAITS FOR A PERSON TO RESPOND NOTE: THE CONSOLES CALLED HAVE 60 SECONDS TO RESPOND, OR THE CALL WILL BE CANCELED STATION INDICATOR LIGHTS TO SHOW WHICH STATION CALLED GARAGE HEARS KITCHEN CALL GARAGE CONSOLE 3 HAVE THE CONVERSATION RESPOND TO THE CALLER BY PRESSING & HOLDING THE ALL CALL BUTTON WHILE SPEAKING, RELEASE THE ALL CALL BUTTON AFTER SPEAKING (WAIT FOR BEEP BEFORE TALKING) THE CONVERSATION GOES BACK AND FORTH, WITH EACH PERSON PRESSING THEIR OWN ALL CALL BUTTON CONSOLES WILL GO ON STANDBY AFTER 60 SECONDS OF NO TALKING STATION INDICATOR LIGHTS WHILE TALKING AND LISTENING GARAGE TALKS TO KITCHEN GARAGE CONSOLE ADJUSTING THE DOORBELL’S VOLUME THE DOORBELL'S VOLUME CAN BE ADJUSTED TO SUIT THE INSTALLATION HAVE SOMEONE TALK TO THE DOORBELL FROM THE CONSOLE WHILE ADJUSTING THE DOORBELL'S VOLUME USE A SMALL SCREWDRIVER TO ADJUST THE VOLUME CONTROL DOORBELL VOLUME LOW HIGH CHANGING A CONSOLE’S SETTINGS 1 THE FACTORY SETTING FOR THE FREQUENCY SWITCH IS "A", SET THE FREQUENCY SWITCHES TO MATCH ON ALL CONSOLES (ALL EITHER "A" OR "B") 1. START WITH THE POWER OFF (VOLUME KNOB OFF) 2. PRESS & HOLD DOWN "ALL CALL" & "TALK" BUTTONS 3. TURN POWER ON (TURN VOLUME KNOB ON HALFWAY) 4. WHEN ALL STATION LIGHTS FLASH, RELEASE THE BUTTONS TO CHANGE A CONSOLE OR ADD A NEW CONSOLE, PREPARE THE CONSOLE FOR PROGRAMMING NOTE: UNITS ARE PRE-SET AT THE FACTORY WITH THE SAME HOUSE CODE, CHANGING THE HOUSE CODE IS ONLY NECESSARY WHEN ADDING ADDITIONAL UNITS OR TO AVOID OVERLAP WITH OTHER SYSTEMS SET THE MUTE SWITCH TO OFF WHILE PROGRAMMING 2 1. PRESS A NUMBER BUTTON TO SET THE CONSOLE'S STATION NUMBER (SELECT A DIFFERENT STATION NUMBER FOR EACH CONSOLE) 2. THE SELECTED STATION NUMBER INDICATOR WILL FLASH SET THE CONSOLE'S STATION NUMBER SETTING THE CONSOLE'S STATION NUMBER NOTE: TO EXIT PROGRAMMING WITHOUT CHANGING THE HOUSE CODE NUMBER, PRESS THE TALK BUTTON TWICE 3 1. PRESS AND RELEASE THE TALK BUTTON 2. THE CONSOLE WILL BEEP, COUNTING THE EXISTING HOUSE CODE NUMBER 1. PRESS THE ALL CALL BUTTON 1 TO 15 TIMES TO SET THE NEW HOUSE CODE NUMBER 2. THE CONSOLE WILL BEEP, COUNTING THE NEW HOUSE CODE NUMBER 3. PRESS THE TALK BUTTON TO EXIT PROGRAM MODE SET THE CONSOLE'S NEW HOUSE CODE NUMBER NOTE: ALL UNITS MUST BE SET TO THE SAME HOUSE CODE NUMBER TALK BUTTON MAKES THE CONSOLE SOUND THE EXISTING HOUSE CODE NUMBER ALL CALL BUTTON ENTERS THE NEW HOUSE CODE NUMBER FACTORY SETTING: HOUSE CODE = 10 CHANGING A DOORBELL’S SETTINGS B A 1 TO CHANGE A DOORBELL OR ADD A NEW DOORBELL 5 4 NOTE: UNITS ARE PRE-SET AT THE FACTORY WITH THE SAME HOUSE CODE, CHANGING THE HOUSE CODE IS ONLY NECESSARY WHEN ADDING ADDITIONAL UNITS OR TO AVOID OVERLAP WITH OTHER SYSTEMSTHE FACTORY SETTING FOR THE FREQUENCY SWITCH IS "A", SET THE FREQUENCY SWITCH TO MATCH THE CONSOLE (EITHER "A" OR "B") THE FACTORY SETTING FOR THE STATION SWITCH IS "5", SET THE STATION SWITCH TO EITHER "4" OR "5" CHIME SOUND: 5 = "DING-DONG" 4 = "DONG" 1. BE SURE THE GREEN POWER LIGHT IS OFF (IF THE LIGHT IS ON, WAIT ABOUT 2 MINUTES) 2. USE AN OBJECT TO PRESS AND HOLD THE PROGRAM BUTTON UNTIL A BEEP SOUNDS 3. RELEASE THE PROGRAM BUTTON (BE READY TO COUNT BEEPS) 4. THE DOORBELL WILL BEEP, COUNTING THE EXISTING HOUSE CODE NUMBER PROGRAM BUTTON INSIDE HOLE PLACE THE DOORBELL INTO PROGRAM MODE AND COUNT THE EXISTING HOUSE CODE NUMBER BEEPS2 DOORBELL BEEPS THE EXISTING HOUSE CODE NUMBER FACTORY SETTING: HOUSE CODE = 10 1. PRESS THE TALK BUTTON 1 TO 15 TIMES TO SET THE NEW HOUSE CODE NUMBER 2. THE DOORBELL WILL BEEP, COUNTING THE NEW HOUSE CODE NUMBER SET THE DOORBELL'S NEW HOUSE CODE NUMBER3 3. PRESS THE PROGRAM BUTTON TO EXIT PROGRAM MODE DOORBELL BEEPS THE NEW HOUSE CODE NUMBER NOTE: ALL UNITS MUST BE SET TO THE SAME HOUSE CODE NUMBER TROUBLESHOOTING SYMPTOM REMEDY POWER INDICATOR WILL NOT LIGHT BE SURE THE CONSOLE TRANSFORMER IS PLUGGED INTO AN UN-SWITCHED OUTLET BE SURE THE DOORBELL UNIT HAS FRESH 9-VOLT ALKALINE BATTERIES EXCESSIVE HUM FROM THE SPEAKER KEEP CONSOLE AWAY FROM FLUORESCENT LIGHTS MOVE DOORBELL UNIT IF IT IS NEAR AN AC LINE SYSTEM FAILS TO WORK AT DISTANCE BE SURE THE CONSOLE ANTENNA IS POINTED UP MOVE UNITS AROUND TO DETERMINE BETTER RECEPTION LOCATIONS SYSTEM RECEIVES VOICE SIGNALS FROM NON-RELATED EQUIPMENT CHANGE THE FREQUENCY SWITCHES ON EACH UNIT (ALL UNITS MUST BE ON THE SAME FREQUENCY) CHANGE THE HOUSE CODE SYSTEM RECEIVES ELECTRICAL NOISE MOVE UNITS AWAY FROM COMPUTERS, ELECTRIC MOTORS, LIGHT DIMMER SWITCHES, ETC. SYSTEM FAILS TO FUNCTION PERFORM THE SYSTEM PROGRAMMING AGAIN MOVE UNITS AWAY FROM METAL OBJECTS SYSTEM FUNCTIONS...

Herunterladen

Geben Sie zwei Ziffern: