Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: ClearSounds Dateigröße: 224.48 kb Dateiname: a353c6a0-73cc-4de4-88bb-4f369b29c0f1.pdf Unterrichtssprache:

LAST NUMBER REDIAL To redial the last telephone number you dialed, press the LNR key or dial 19. NOTES: 1. If the Hot Keypad feature has been turned off, you must first lift the handset or press SPK or MONITOR before you begin dialing. 2. Redial does not apply to intercom calls. MANUAL RETRY WITH LNR While you are on an outside call listening to a busy signal and you want to redial the same number dialed. • Press the LNR key. This will hang up your existing call and manually redial the same number dialed. You can repeat this operation for a limited number of attempts. SAVE NUMBER WITH REDIAL To save the number you just dialed for later use, press the SNR key before hanging up. To redial this saved number at any time, press the SNR key or dial 17. The same line will be selected for you. NOTES: 1. If the Hot Keypad feature has been turned off, you must first lift the handset or press SPK or the MONITOR key if you are using a 7B phone before you begin dialing. 2. The saved telephone number is stored in memory until you save another. 3. Redial does not apply to intercom calls. CHAIN DIALING You may manually dial additional digits following a speed dial number or chain as many speed dial numbers together as required: • After the first speed number is dialed, press SPD again and dial another speed number OR manually dial additional digits following a speed dial number. AUTOMATIC REDIAL/RETRY When you are making an outside call and you receive a busy signal, the can automatically redial the number for you. It will automatically redial at a pre-programmed interval for up to 15 attempts. • When you hear a busy signal, press the RETRY button. • The system will reserve the line and automatically redial the same number for you. You will hear the call being made through the keyset speaker. The microphone is muted. • When the called party answers, lift the handset or press the flashing SPK to begin speaking. NOTES: 1. If you make another call, auto-redial is canceled. 2. To cancel a retry, lift and replace the handset. PULSE TO TONE CHANGEOVER When making an outside call on a dial pulse line, press # . All digits dialed after the # with be sent as tones. MEMO When you are calling given using the SAVE feature. There is no need for pencil and paper. • While you are talking on an outside SAVE. • Dial the telephone number • Press SAVE to store the number. To dial the number, press the SNR button. It will select the same line and dial stored number. If necessary, you can select a different line and then press the SNR button. PAGING AND MAKING AN To make an announcement through speakers: • Lift the handset. • Press the PAGE key or dial 55. • Dial the desired zone number 1, 2, 3 or 4. OR Dial 0 to page all internal zones. • After the attention tone, make your announcement. NOTE: If you have a dedicated page zone key, it is not necessary to press PAGE and dial a zone number. MAKING AN EXTERNAL PAGE To make an announcement through the external paging speakers: • Lift the handset. • Press the PAGE key or dial 55. • Dial the desired zone number 5, 6, 7 or 8. OR Dial 9 to page all external zones. • After the attention tone, make your announcement. NOTE: If you have a dedicated page zone key, it is not necessary to press PAGE and dial a zone number. ALL PAGE To page all designated keysets and external speakers at the same time: • Lift the handset. • Press the PAGE key or dial 55. • Dial . or press the ALL PAGE key. • After the attention tone, make your announcement. NOTE: The LED on the PAGE key will only light when an All Page is in progress. MEET • Lift the handset. • Press the Meet Me ( MMPG) key or dial 54. • Dial the desired zone number. • After the attention tone, 56. • Press WAIT or TRSF. • Remain off-hook until the person 56 from any phone. • The paged person will be automatically CALL PARK AND PAGE When you have an outside call for someone park the call prior to paging. The DCS 400si offers two different methods: MANUAL PARK ORBITS • While in conversation, press the PARK button. • Enter a desired orbit number ( 0-9), if the orbit number is busy dial another orbit number. Display users can press . to automatically place the call in any available orbit number and see the number in the display. • Remember the selected orbit number. • Replace the handset when finished. • Lift the handset and make a page announcement as previuosly described (example: “ John Smith park two” ). To retrieve a parked call from orbit: • Press the PARK button and dial the announced orbit number ( 0-9). • You will be connected to the parked call. NOTES: 1. You must have a PARK button or park access code to retrieve and place calls in park orbits. 2. If the call is not retrieved within a pre-programmed period of time, it will recall your keyset and have a slow amber light. You cannot park and page intercom calls. 3. If the Hot Keypad feature has been turned off, you must first lift the handset or press SPK before you begin dialing. AUTOMATIC PARK WITH PA...

Herunterladen

Geben Sie zwei Ziffern: