LP-ET30L Throw Distance(Aspect ratio horizontal:vertical ^4:3) Throw Distance:unit(m) Type On-Axis Short Fixed Lens Short Zoom Lens Standerd Zoom Lens Long Zoom Lens Ultra Long Zoom Lens Part Number LNS-W11 LNS-W10 LNS-S11 LNS-T10 LNS-T11 Zoom/Focus Fixed/Manual x1.3/Power x1.3/Power x1.6/Power x1.6/Power Twin stack support X X X X X Focal length(mm) 16.51 25~33 33~43 43~69 69.1 — 109.2 F value 2.3 2.3~2.6 1.7 — 2.1 2.0~2.6 2.1—2.52 lens aperture (mm) 97 9

LNS-M01 LNS-S01 LENS REPLACEMENT AND INSTALLATION PROCEDURE NOTES ON LENS INSTALLATION Lens installation should be performed by the qualified service personnel. It should be followed by this procedure precisely. Before attempt to install the lens, confirm the model number (both the LCD projector and the lens) and use the proper lens. If you have any questions, contact to the dealers. PARTS LIST Following parts are contained in the packing. • LENS 1 piece • LENS MOUNTING SCREWS 6 screw

(Refer to Figure 1) 2. Pull out the terminal by holding the handle. 3. Replace the terminal. Insert the terminal along Guide to fit Plug into Socket. (Refer to Figure 2) 4. Tighten the screws to secure the terminal. ♦ These figures show the case of replacing with HDB 15-PIN terminal. Figure 1 Screws Figure 2

(Refer to Figure 1) 2. Pull out the terminal by holding the handle. 3. Replace the terminal. Insert the terminal along Guide to fit Plug into Socket. (Refer to Figure 2) 4. Tighten the screws to secure the terminal. ♦ These figures show the case of replacing with HDB 15-PIN terminal. Figure 1 Screws Figure 2

(Refer to Figure 1) 2. Pull out the terminal by holding the handle. 3. Replace the terminal. Insert the terminal along Guide to fit Plug into Socket. (Refer to Figure 2) 4. Tighten the screws to secure the terminal. ♦ These figures show the case of replacing with HDB 15-PIN terminal. Figure 1 Screws Figure 2

LNS-W02/T02 LNS-W02K/T02K Series LENS REPLACEMENT AND INSTALLATION PROCEDURE NOTES ON LENS INSTALLATION Lens installation should be performed by the qualified service personnel. It should be followed by this procedure precisely. Before attempt to install the lens, confirm the model number (both the LCD projector and the lens) and use the proper lens. If you have any questions, contact to the dealers. PARTS LIST Following parts are contained in the packing. • LENS 1 piece • LENS MOUNTI

(See figure-4) 1. Remove the connector “K16B” of the circuit board. 2. Loosen the A, B, C wire holder and remove the lens motor lead. 3. Remove screws D (4 screws) which fastens the lens and remove the lens. Fig-4 3 INSTALL THE LENS. (See figure-4,5) 1. Remove protective caps (front and back ) on the lens. 2. Mount the lens at the lens mounting bracket with screws (4 screws) included with the lens. Use the driver included with the lens to fasten the screws . (After using, save it for latt

Remove the protective caps (front and back) on the lens. 2. Insert the lens into the Lens Bracket of the projector asmatching the red mark on the lens to that on the LensBracket. 2 -2Fig- 2 Red mark 3. Slowly turn the lens clockwise until it clicks. Make sure thatthe lens is fully inserted to the projector. Lens Replacement Procedure (For B type Cabinet) (For B type Cabinet) Perform the steps 1-6 for lens replacement. First set the lens at the lowest position with lens shift adjustment. 1 Remove

Mount the top cabinet with 2 screws. 2. Push into the Lens Cover to the Top Cabinet. Confirm the top and bottom of the lens cover. The part circled in Fig-6-2 should be fitted. {When LNS-W11 (AH-23631) is installed, the LensCover is unnecessary.} Turn the projector on and check Lens shift, Zoom and Focus is operating properly. If Light-Block Sheet interfere with those operations, check if the Light-Block Sheet is set properly. LNS-W11 (AH-23631) cannot adjust the Zoom and Focus at the Remote con

Before an attempt to replace the lens, confirm the model number (both the LCD projector and the lens) and prepare the proper lens. Lens installation is different in cabinet design (Type A and B). Before installation the lens, check cabinet design should be made. The lens cover is on the lens for protection. Be sure to remove the lens cover before installation. When installing or removing the lens, be careful not to stain, scratch or damage the lens. If you have any questions, contact the dealers