Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Otherwise, it may significantly reduce the battery life. .................................. M.VOL - VOL + 30° 30° PAGE3DL / RMARKVOLSETTINGS3DL Using the PROJECTOR Watching Projector Turning on the Projector 1 Connect the power cord correctly. yyCheck if the lens cap is open before turning on the projector. 2 After waiting for a moment, press the POWER button on the remote control or the control panel. (The light on the control panel will be turned on.) 3 In the Language Selection screen, select a language. 4 Select an input signal by using the INPUT button on the remote control. Focus and Position of the Screen Image When an image appears on the screen, check if it is in focus and fits the screen properly. Focus ring yyTo adjust the focus of the image, rotate the focus ring. Watching Projector 1 In Standby mode, press the POWER button to turn the projector on. 2 Press the INPUT button and select the input signal you want. 3 Control the projector using the following buttons while watching projector. Button Description VOL -, + Adjusts the volume level. MUTE Mutes all sounds. Q.MENU Accesses the quick menu. (see page22) RATIO Resizes an image. Key's.,. Adjusts Keystone. (see page21) 4 To turn the projector off, press the POWER button. Using Additional Options Adjusting Aspect Ratio Resize an image to view at its optimal size by pressing RATIO while you are using the projector. NOTE yySome options may not be available depending on input signals. yyYou can also change the image size by pressing Q.MENU or SETTINGS. - FULL: Changes to the full screen regardless of the aspect ratio. - 16:9: Resizes images to fit the screen width. - Just Scan: Displays video images in the original size without cutting off the edges. NOTE yyIf you select Just Scan, you may see image noises at the edge or edges of the screen. - Set By Program: Displays images in the same aspect ratio as the original image. - 4:3: Resizes images to the 4:3 aspect ratio. - Zoom: Enlarges an image to fit the screen width. The top and bottom of the image may be truncated. yyPress the . or . button to zoom in or out of the image. yyPress the . or . button to move the image. - Cinema Zoom: Formats an image to the cinemascope ratio, 2.35:1. It ranges from 1 to 16. yyPress the . or . button to zoom in or out of the image. yyPress the . or . button to move the image. NOTE yyIf you enlarge or reduce an image, the image may be distorted. Using the Keystone Function To prevent the screen image from becoming trapezoidal, Keystone adjusts the top and bottom width of the image if the projector is not set at a right angle to the screen. Because the Keystone function may cause inferior screen image quality, use this function only when it is not possible to set up the projector at an optimal angle. •Keystone 0.- +. . OK 1 Press the Key's. or Key's. button to adjust the screen. yyKeystone can be adjusted from -40 to 40. 2 Press the OK button after adjustment. Using the Input List Using the Input List 1 Press the INPUT button to access the input sources. - The connected input mode appears first. However, AV / Component input is always activated. INPUTINPUTComponentUSBRGB-PCHDMI . Move . OKExitInput Label 2 Select an input signal using the INPUT button and the projector is switched only to the connected input mode. You can use the ., ., . or . button to switch between all the input modes. Adding an Input Label Displays which devices are connected to which input ports. Input LabelINPUT.. Component.. RGB-PC.. HDMI.. Close 1 Press the INPUT button to access the input sources. 2 Press the BLUE button. 3 Use the . or . button to scroll to one of the input sources. 4 Use the . or . button to select one of the input labels. Blank Function Using the Blank Function This function may be effective when you need to draw attention during a meeting or training. 1 Press the BLANK button, and the screen is covered by the background color. You can change the background color by referring to "Selecting a Blank Image". 2 Press any button to clear the blank function. To cover the screen temporarily, press the BLANK button on the remote control. Do not block the lens with any object while the projector is running. It may become overheated and deformed or even cause a fire. Selecting a Blank Image 1 Press the SETTINGS button. 2 Press the ., ., . or . button to select OPTION and press the OK button. 3 Press the ., ., . or . button to select Blank Image and press the OK button. 4 Use the ., . button to move to the setting or option you want and press the OK button. Using the Quick Menu You can customize frequently used menus. 1 Press Q.MENU to access the quick menus. 2 Press the . or . button to scroll through the following menus and press OK. Menu Description Aspect Ratio Resizes an image. (see page20) Picture Mode Changes the picture mode. (see page44) Energy Saving Adjusts brightness. Clear Voice II Makes the voice from the projector crisp and clear. Sound Mode Set each option as desired. ...