Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
(BNC) S-VIDEO IN terminal (page 22) An input terminal for S-video signals. (MIN4-pin DIN) This terminal complies with S1 signals and automatically toggles between 16:9 and 4:3 according to the size of input signals. RGB 1 input (RGB 1 IN) terminal (page 22) A terminal to input RGB or YPBPR signals. (BNC) RGB 2 input (RGB 2 IN) terminal (page 22) A terminal to input RGB or YPBPR signals. (D-SUB 15-pin female) DVI-D IN terminal (page 22) DVI-D signals are applied to this terminal. (24-pin DVI connector) LAN terminal (page 38) This terminal is used to control the projector from the PC. (10Base-T/100Base-TX compliant) LAN terminal (10Base-T/100Base-TX) Connect LAN cable. LAN 10/100 lamp (Yellow) Lights up when 100Base-TX connected. LAN LINK/ACT lamp (Green) Lights up when connected. Flashes when receiving/sending signals. REMOTE1 lN/OUT terminal (page 16) When two or more main units are used in the system, they can be connected and controlled with M3 stereo mini jack cable available in the market. REMOTE2 IN terminal The user can remotely control the main unit by using an external control circuit to this terminal. (D-SUB 9-pin female) SERIAL IN terminal (pages 22, 39) Use the RS232C serial terminal as an alternative interface for controlling the projector from your PC. (D-SUB 9-pin female) SERIAL OUT terminal (pages 22, 39) The signal applied to the serial input terminal appears at this terminal. (D-SUB 9-pin male) Using the remote control unit Loading dry cells When loading batteries into the battery compartment of the remote control, make sure that their polarities are correct. 1.Open battery compartment lid. Open the lid in the order of steps and . 2.Insert the dry cells. Into battery compartment, with their polarities orientated as indicated ( , ) in the compartment. 3.Close the battery compartment lid. Replace the battery compartment lid over the compartment and slide until it clicks. illustrated in figure 2. The effective control range is approx. 7 meters from the beam receiver on the front or rear. Accessory type-AAA dry batteries (insert the negative side first). (Front) (Rear) [Top view] [Side view] Remote control Remote control Remote control Remote control 15° 15° 15° 15° 30° 30° 30° 30° Remote control receiver window (rear) Remote control receiver window (front) Projector Remote control Screen Figure 1 Figure 2 Effective range of remote control operation The remote control should normally be aimed at either the front or rear remote control receiver window on the projector (figure 1). Otherwise, it may also be aimed at the screen, which will reflect commands back to the projector’s front receiver window as Attention • Do not drop the remote control unit. • Do not expose remote control unit to any liquid. • Do not use NiCd batteries. Note • When the remote control is aimed at the screen, the effective control range may be reduced due to the optical loss by screen reflection. • The remote control may not function properly if an object is in the light path. • The remote control receiver may not function properly in intense ambient light such as fluorescent lamps. Carefully site the projector so its remote control receiver windows will not be directly exposed to intense light. Setting projector ID number to remote control Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. The ID number of the projector is set to “ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector. Procedure of ID setting Change the position of the operation mode selector switch to “Computer”. Press the ID SET button, and within five seconds use the number (0 to 9) buttons to enter the 2-digit ID number set by the projector. Change the position of the operation mode selector switch to “Projector”. However, if the ID ALL button is pressed, the projector can be controlled regardless of the ID number of the projector (simultaneous control mode). Attention • Do not press the ID SET button accidentally or carelessly because the ID number on the remote control can be set even when no projector is around. If the ID SET button is pressed, the ID number goes back to the one set before pressing the ID SET button unless a numeric button is pressed within five seconds after the ID SET button is pressed. • Your specified ID number is stored in the remote control unit unless another one is specified later. However, the stored ID will be erased if the batteries of the remote control are left exhausted. When the dry cells are replaced, set the same ID number again. • When specifying the ID number, enter a 2-digit number even if the ID has only one digit. (Example: set “02” if the ID number is “2.”) Using the remote control as a PC mouse PAGE UP button ENTER button Left click Right click ( ) button ( ) button PAGE DOWN button Operation mode selector switch Click button Operation mode ...