Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or EN injury from possible battery leakage. • Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. IR SIGNAL CHECK Use the AM radio or the digital camera to check if the remote control properly sends out the infrared signal. It will help to define the cause of malfunction. Using AM radio • Tune the AM radio to no broadcasting band. Press any button on remote control toward the radio. If the radio receives the signal from remote control properly, the sound will flutter. Using digital camera (including built-in camera of cellular phone) • Press and hold any button on remote control toward a digital camera. The remote control is working if you confirm infrared light through the digital camera. - 8 PREPARATION FOR USE ANTENNA/CABLE CONNECTIONS Plug the incoming cable into the ANT. jack on the rear of the unit. If your cable service supplies you with a converter box or if you use a satellite system, connect the box with this unit as shown below. Cable TV signal AntennaOR ANT. ANT. IN OUT Rear of the unit *NOTE (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company. OR Incoming cable from home Antenna / Cable Company (No Cable Box) Incoming cable from Cable Company or Satellite Antenna Cable Box or Satellite Box* Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. NOTE: Before plugging the antenna into the ANT. jack of the unit, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the ANT. jack of the unit. Bent pin Rod Antenna Connection: You can use the Rod Antenna (Supplied) if incoming cable is not available. Cable Plug (Needs to bestraightened) (Straight pin) ANT. ANT. For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack before moving the unit. - 9-EN USING FRONT A/V INPUT JACKS USING FRONT A/V INPUT JACKS When you watch a program recorded on another source (VCR or video camera), use the AUX AUDIO/VIDEO input jacks on the front of the unit. Connect the Audio/Video output jacks of another source to the AUDIO and VIDEO jacks of this unit. Then use [CHANNEL K KK/L LL] until “AUX” appears on the screen. VIDEO AUDIO POWER VOLUME CHANNEL STOP/EJECT REW PLAY F.FWD REC/OTR EARPHONE VIDEO AUDIO ex. VCR or video camera, etc. [Front of the unit] To the Audio output jack To the Video output jack (OUT)(IN) (OUT) (IN) Audio cable (commercially available) Video cable (commercially available) TV OPERATION AND SETTINGS WATCHING A TV PROGRAM 1 Plug in the power cord After antenna or cable connection is completed, connect the power cord into a standard AC outlet. NOTE: • If any digits appear in the corner of the screen, press [POWER] without unplugging the power cord. 2 Turn on the unit Press [POWER] to turn on the unit. 3 Select the channel number Use [CHANNEL K KK/L LL] or the Number buttons to select your desired channel number. Note for using the Number buttons: .You must precede single-digit channel numbers with a zero (for example: 02, 03, 04 and so on). .When selecting cable channels which are higher than 99, press [+100] first, then enter the last two digits. (Example: to select channel 125, first press [+100] then press [2] and [5].) 4 Adjust sound Use [VOLUME X XX/Y YY] to adjust the volume. VOLUME 20 Press [MUTE] to instantly mute C C C C C C C C C C C C the sound. Press it again to restore the previous sound level. TO WATCH CABLE OR SATELLITE CHANNEL • If the unit is connected to a cable box or satellite box, use [CHANNEL K KK/L LL] to select CH3 or CH4 according to the output channel setting of the device and select desired channel on that device. TO WATCH EXTERNAL INPUT • When an external equipment is connected to the front AUDIO/VIDEO input jacks, use [CHANNEL K KK/L LL] repeatedly until “AUX” appears on the screen. EN - 10 CHANNEL SET UP CHANNEL SET UP Make sure ... • The unit must be turned on. AUTO CHANNEL PROGRAMMING As the initial setting, this unit has memorized all channels, including the ones not available in your area. This feature automatically puts only available channels into the memory. 1 Select “CHANNEL SET UP” – M E N U – Press [MENU]. TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK B CHANNEL SET UP USER’S SET UP Use [PLAY/K KK] or [STOP/L LL] to point to “CHANNEL SET UP”, V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH then press [F.FWD/B BB]. 2 Begin channel scanning – CHANNEL SET UP – Use [PLAY/K KK] or [STOP/L LL] to ADD / DELETE CH (CATV) point to “AU...