Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Changes or modifications not expressly approved by the party responsible for FCC compliance could void the user's authority to operate the equipment. For Canadian customers: "This digital apparatus does not exceed the class A limit for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled "Digital Apparatus" "ICES-003 of Industry Canada". All content herein is the property of The Stanley Works, its Affiliates, or their content suppliers and is protected by United States and international copyright laws. The compilation of all content is likewise the exclusive property of The Stanley Works (or the Affiliate identified in any copyright notice) and is protected by United States and international copyright laws. The trademarks, service marks and logos (the 'Trademarks') used and displayed in this publication are registered and unregistered Trademarks of The Stanley Works, its Affiliates and others. Nothing herein should be construed as granting, by implication, estoppel or otherwise, any license or right to use any Trademark displayed herein without the prior consent of the Trademark owner. Micro-Tech and the Micro-Tech design are some of the registered and unregistered trademarks owned by The Stanley Works and/or its Affiliates ("Stanley Trademarks"). Stanley Trademarks may not be used in connection with any product or service that is not manufactured by or under license from The Stanley Works or its appropriate Affiliate. Micro-Tech is a trademark of Stanley Logistics, Inc. © 2007 The Stanley Works Printed in China Read these installation instructions thoroughly before using the Informer-Mate™ system. Failure to do so may result in injury or death to a person in your care. Test the Informer-Mate™ control unit and sensor pad before each use and inspect the cords and sensor pads for signs of damage. Replace any components with signs of wear or damage immediately. The Informer-Mate™ system is only one part of your facility's fall management program. The Informer-Mate™ system is not a substitute for proper nursing care or routine visual monitoring by caregivers. The effectiveness of the Informer-Mate™ system relies entirely on an immediate response by the caregiver to the Informer- Mate™ system alarm. The Informer-Mate™ system will not stop a person from leaving a bed or chair. It is intended only to alert a caregiver that a patient or resident may need assistance. The Informer-Mate™ system can be defeated by a cognitively aware person, a person with only a few moments of lucidity, or an uncooperative person. Properly assess each individual before the Informer-Mate™ system is used. Resident weight may affect proper operation. Models 82700, 82708, 82710, 82715, 83700 and 83705 pressure pads are not recommended for persons weighing less than 60 lbs. Keep the sensor pad flat at all times. Folding the pad will damage it. Do not use the pad if it has been folded. Sensor pads were designed to withstand normal wear and tear, but are more likely to fail and fail without warning due to prolonged use and other factors, e.g. bending, exposure to moisture, punctures, repeated cord pulls, connector damage, etc. Test each pad before each use and remove it from service at any sign of damage or at the end of the stated life of the pad (as labeled on it), whichever comes first. Use care when installing the Informer-Mate™ system. Gently remove or connect cords. Pulling on cords may damage them and/or result in system failure. When putting your sensor pads into position, keep the pad face up. Failure to do so will result in reduced sensitivity and improper operation of your Informer- MateTM system. Replace the battery immediately if the red low battery light on the control unit is on. The control unit will not function properly with a low battery. Do not immerse the sensor pads in liquids. The pad will not operate properly if the sensor pad is exposed to excessive liquids. If the pad is immersed in liquid, discard it immediately. Description of the Micro-Tech® Informer- Mate™ Series Monitoring Systems Before installing this system, please read and follow these instructions carefully. Failure to do so could result in injury or death to a person in your care. No device is a substitute for proper nursing care. The Micro-Tech® Informer-Mate™ system is designed to help reduce the risk of falls by alerting caregivers when a resident is leaving a bed, chair, or wheelchair. Mount the monitor on the bed, chair or wheelchair using one of the Micro-Tech® mounting brackets according to the included instructions. Place a Micro-Tech® pressure pad on the bed, chair or wheelchair according to the instructions included with the pad and attach the cord to the monitor. When a resident moves from the pad, an alarm sounds, alerting you of a potential fall risk. Monitor Design The Micro-Tech® Informer-Mate™ series incorporates several important features, allowing you to focus on resident ca...
Dieses Handbuch ist für folgende Modelle:Andere persönliche Geräte - INFORMER-MATE 81791 (135.41 kb)