Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Micro Technic Dateigröße: 135.41 kb Dateiname: Unterrichtssprache:

Folding the pad may damage it. Do not use the pad if it has been folded. Check for proper operation of the Informer-Mate™ system with each mattress type used. Above the mattress set-up 1. Place the bed sensor pad across the width of the bed and under any sheets, overlays or incontinence pads (Figure 4). Placement should be under the patient or resident's buttocks area. Sensor Sensor wire Informer-Mate™ control unit Pad overlay Figure 4 2. Using the band and clip package provided with the sensor pad, fasten the sensor pad to the mattress (Figure 5). Make sure the sensor pad is fastened securely and lies flat against the mattress. Rubber band Clip Bead of Side of mattress Sensor mattress Figure 5 3. Route the sensor pad cable from the sensor pad to the control unit. The cable will need to run from the top of the mattress to the underside of the bed and up the headboard, footboard, or rail of the bed (Figure 4). Make sure the cable lies freely and does not interfere with handrails or moving parts of the bed. 4. Mount the control unit on the bed headboard, footboard, or rail in a convenient location using the mounting strap or mounting bracket. Optional wide mounting brackets are available for extra wide headboards and footboards. 5. Insert the sensor pad cable into the sensor pad receptacle on the control unit. 6. If you are using the Informer-Mate™ Deluxe system, set the desired alarm tone by sliding the volume switch to position 1, 2, 3 or 4. If connecting a nurse call cable to the deluxe unit, the alarm will, when sounding, automatically be sent to the nurse call unit and the local alarm will be disabled. 7. Test the Informer-Mate™ monitoring system before each use and inspect the pads and monitor regularly to make sure they are not damaged. Test the system by pressing firmly on the pad for 3 seconds. When you remove pressure, the alarm should sound. Reset the alarm using the 2-button reset. Installing the Informer-Mate™ System On a Chair Informer-Mate™ control unit Sensor pad Chair setup 1. Place the chair sensor pad on the seat portion of the chair (Figure 6). An additional cushion may be used on top of the pad for patient or resident comfort. If you use an additional cushion, test the system by pressing firmly on the top of both cushions. 2. Mount the control unit on the chair in a convenient location with the mounting clip or Figure 6 mounting strap provided. 3. Insert the sensor pad cable into the sensor pad receptacle on the control unit. 4. If you are using the Informer-Mate™ Deluxe system, set the desired alarm tone by sliding the volume switch to position 1, 2, 3 or 4. If connecting a nurse call cable to the deluxe unit, the alarm, when sounding, will automatically be sent to the nurse call unit and the local alarm will be disabled. 5. Test the Informer-Mate™ monitoring system before each use and inspect the pads and monitor regularly to make sure they are not damaged. Test the system by pressing firmly on the pad for 3 seconds. When you remove pressure, the alarm should sound. Reset the alarm using the 2-button reset. Maintenance To keep your Informer-Mate™ control unit in good condition: • Do not immerse the control unit in liquid of any type. The control unit will not operate properly if exposed to excessive liquids. If the control unit is immersed in liquid, discard it immediately. • Gently clean the Informer-Mate™ control unit with non-caustic cleaning agents. • Test your Informer-Mate™ control unit and sensor pad before each use and inspect the cords, controls and sensor pads for signs of damage. Replace any components with signs of wear or damage immediately. Never use equipment that has been damaged. • Call your distributor or Micro-Tech at 800-206-1045 to order replacement parts. To keep your sensor pads in good condition: • Do not immerse the pressure pad in liquid of any type. The pressure pads will not operate properly if exposed to excessive liquids. If the pad is immersed in liquid, discard it immediately. • Clean soiled areas of sensor pad with a clean cloth and water or a vinyl-tolerant solution. • Keep the pressure pad flat at all times. Folding the pad will damage it. Do not use the pad if it has been folded. • Call your distributor or Micro-Tech at 800-206-1045 to order replacement parts. Warranty and Disclaimer WARRANTY AND DISCLAIMER: Micro-Tech® products are warranted to be free of manufacturing defects for a period of one year from the date of purchase. If any defects covered by this Warranty appear within the above stated one year period, Micro-Tech will, at its option, repair or replace the defective component on an exchange basis with new or rebuilt parts at its expense, without charge for parts or labor upon delivery of such product to Micro-Tech at Buyer’s expense. EXCEPTION: MICRO-TECH® PADS AND ACCESSORIES ARE WARRANTED TO BE FREE OF MANUFACTURING DEFECTS FOR PERIODS RANGING FROM 30 DAYS TO 1 YEAR AS SPECIFIED TO BUYER. Micro-Tech is not responsible for warranty servi...

Herunterladen

Geben Sie zwei Ziffern: