READ AND KEEP FOR REFERENCE. INSTRUCTIONS Rev. D Supercedes Rev. C Pressure Roller Equipment 300 psi (21 bar) MAXIMUM WORKING PRESSURE Operate your pump at the lowest pressure needed for sufficient paint supply to your roller Adjustable Extension Roller Kit 218–625 Includes Roller Frame, 18–36 in. Extension Tube, 3/8 in. nap Roller Cover and 45 Gun Adapter Adjustable Extension Tubes 218–775 18–36 in. (0.45–0.9 m) 218–776 3–6 ft (0.9–1.8 m) 218–777 6–12 ft (1.8–3.7 m) *45 Gun Adapter 218–932 1/4

Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings. FIRE AND EXPLOSION HAZARD . If there is any static sparking or you feel an electric shock while using this equipment, stop dispensing immediately. Do not use the equipment until you identify and correct the problem. . Keep the dispensing area free of debris, including solvent, rags, and gasoline. . Electrically disconnect all equipment in the dispensing area. . Extinguis

. Do not stop or deflect leaks with your hand, body, glove or rag. . Tighten all connections before operating the equipment. . Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately. Permanently coupled hoses cannot be repaired; replace the entire hose. . Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings. FIRE AND EXPLOSION HAZARD . If there is any st

For storage, flush the system with Graco Pump Armor or mineral spirits/paint thinner. See Flushing on page 3. WARNING To help prevent injection injuries, follow this procedure whenever you stop painting. psi/MPa/bar 1. Put gun trigger safety in SAFETY ON position. 2. Shut off power to pump. 3. Put pump prime/drain valve (required for pressure relief) in DRAIN position to relieve pressure in system. 4. Put gun trigger safety in SAFETY OFF position, and trigger gun to relieve any pressure in hose.

READ AND KEEP FOR REFERENCE. INSTRUCTIONS Pressure Roller Model 243066, Series A . 20 in. (50 cm) heavy-duty extension . 45 swivel adapter . 9 in. (23 cm) roller frame . 1/2 in. (13 mm) nap roller cover 3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure * This maximum pressure is only possible if the roller frame is * completely plugged. The best operating pressure is the lowest pressure that provides an even paint supply to the roller and typically does not exceed 300 psi (2.1 MPa, 21 ba

See Flushing on page 3. WARNING To help prevent injection injuries, follow this procedure whenever you stop painting. psi/MPa/bar 1. Put gun trigger safety in SAFETY ON position. 2. Shut off power to pump. 3. Put pump prime/drain valve (required for pressure relief) in DRAIN position to relieve pressure in system. 4. Put gun trigger safety in SAFETY OFF position, and trigger gun to relieve any pressure in hose. 5. Put gun trigger safety in SAFETY ON position, and keep pump prime/drain valve in D

Read all warnings and instructions in this manual. Save these instructions. 309323E Pressure Roller with 20” Fixed Extension Model 244279, Series C . 20 in. (50 cm) heavy-duty extension . 9 in. (23 cm) roller frame . 1/2 in. (13 mm) nap roller cover . 45° swivel adapter 3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure * The best operating pressure is the lowest pressure that provides * an even paint supply to the roller and typically does not exceed 300 psi (2.1 MPa, 21 bar). CAUTION Ne

See Cleaning on page 3. 2 309323 Cleaning This is the procedure for flushing the pressure roller. The pump and gun you are using may have additional flushing steps, such as cleaning filters and screens. See the pump and gun flushing instructions. NOTE: Leave the pressure roller attached to the gun for this procedure. See Pressure Relief Procedure on page 2. 1. Relieve the pressure. 2. Remove roller cover (19) and diffuser (23) from roller frame as follows (see Parts Drawing): a. Using your thumb

Attach pressure roller assembly to inline Contractor Inline Valve, use a wrench to tighten. valve. Pressure Relief Procedure WARNING 3. Turn prime/spray valve to PRIME position to relieve pressure in system. To help prevent injection injuries, follow this procedure whenever 4. Put inline valve trigger safety in SAFETY OFF you stop painting. position, and trigger inline valve to relieve any psi/MPa/bar pressure in hose. 1. Put inline valve trigger safety in SAFETY ON position (Fig. 1). 5. Put inl

2. Turn prime/spray valve to SPRAY position. 3. Disengage inline valve safety latch, trigger the inline valve, and roll the surface until paint comes to roller. NOTE: Trigger the inline valve briefly only when you need more paint. Determine how often you must trigger the inline valve to maintain an even paint supply to the roller. 4. Increase pump pressure only if triggering inline valve cannot supply enough paint for your rolling speed. Relieve pressure, page 3, whenever you stop painting. 5. E