Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Graco Inc. Dateigröße: 313.47 kb Dateiname: Unterrichtssprache:

This equipment includes but is not limited to: • Protective eyewear • Clothing and respirator as recommended by the fluid and solvent manufacturer • Gloves • Hearing protection 311141A Pressure Relief Procedure 311141A 3 Pressure Relief Procedure 1. Turn power switch OFF and unplug sprayer power cord. 2. Turn spray/prime valve to PRIME to relieve pressure. 3. Hold metal part of gun firmly to side of a grounded metal pail. Trigger gun. 4. Engage trigger lock. If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved after following the steps above, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Clear hose or tip obstruction. Trigger Lock Always engage the trigger lock when you stop spraying to prevent the gun from being triggered accidentally by hand or if dropped or bumped. Installation 1. Follow pressure relief procedure. 2. Prime pump (refer to your sprayer operation manual for this procedure). 3. Install roller frame. Follow this Pressure Relief Procedure when you stop spraying and before cleaning, checking, servicing, or transporting equipment. .............. .......... ................ .............. Do not modify the extension tube or roller frame or use parts not designed for this equipment. Gasket (12) must be in place before installing frame (1). If gasket is not in place there is a potential injection hazard which could result in serious injury. Refer to your sprayer and spray gun instruction manuals for safe operation of this frame. .............. Cleaning This is the procedure for flushing/cleaning the pressure roller. The sprayer and gun you are using may have additional flushing/cleaning instructions; such as cleaning filters and screens. See sprayer and gun operation manuals. • Leave pressure roller attached to gun for this procedure. • Refer to roller parts drawing, page 1. Relieve pressure, page 3. 2. Remove roller cover (19) and diffuser (23) from roller frame (1) as follows: a. Using your thumb, press down on clip (5) to release end caps (3 & 9), diffuser, (23) and roller cover (19) into pail. b. Remove roller cover (19) from diffuser (23). Cleaning c. Pull end caps (2 & 4) off diffuser (23). 3. Clean roller cover (19), caps (2 & 4) and diffuser (23) with water or a compatible fluid for oil-based materials. 4. Place roller frame (1) in paint pail. Be sure the holes in roller frame (1) are facing inside paint pail. 5. Prime pump with water or flushing fluid for oil-based materials. Use the lowest pump pressure setting. 6. Turn prime/spray valve to SPRAY. Perform Step 7 at the lowest pressure possible. 7. Trigger gun until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of roller frame (1) is clear. 9. Shut off pump. Turn prime/spray valve to PRIME. 311141A Parts Parts Qty. 1 1 1 1 1 1 1 1 2 ................ 4 1 5 9 6 20 19 2 23 Ref. No. Part No. Description 1 15B052 FRAME, roller 2 245999 CAP, end (includes seal and retainer) 4 246277 CAP, end (includes seal, retainer, and o-ring) 5 197106 CLIP, roller 6 197118 FITTING, swivel 9 197117 NUT, retaining 19 7722 ROLLER, cover, 9-inch, 1/2 inch (13mm) nap 20 115524 GASKET 23 15B065 DIFFUSER ^ Replacement Danger and Warning labels,tags, and cards are available at no cost. Roller Covers Part No. Description Qty 7722 9 inch x 1/2 inch nap 6 7723 9 inch x 3/4 inch nap 6 7724 9 inch x 1-1/4 inch nap 6 Wetted Parts: Fluoroelastomer, nylon, plated steel, acetal, polyethylene, stainless steel. 311141A ASM Standard Warranty ASM Standard Warranty ASM warrants all equipment referenced in this document which is manufactured by ASM and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized ASM distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by ASM, ASM will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by ASM to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with ASM’s written recommendations. This warranty does not cover, and ASM shall not be liable for general wear and tear, or any malfunction damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-ASM component parts. Nor shall ASM be liable for malfunction, damage, or wear caused by the incompatibility of ASM equipment with structures, accessories, equipment or materials not supplied by ASM, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by ASM. This warranty is conditioned up the prepaid return of the equipment claimed to be defective to an authorized ASM dis...

Herunterladen

Geben Sie zwei Ziffern: