Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your distributor for information. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. • Do not kink or over bend hoses or use hoses to pull equipment. • Keep children and animals away from work area. • Comply with all applicable safety regulations. SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the body. • Do not put your hand over the spray tip. • Do not stop or deflect leaks with your hand, body, glove, or rag. • Do not spray without tip guard and trigger guard installed. • Engage trigger lock when not spraying. • Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment. PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment. • Tighten all fluid connections before operating the equipment. • Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to: • Protective eyewear • Clothing and respirator as recommended by the fluid and solvent manufacturer • Gloves • Hearing protection 311141A Pressure Relief Procedure 311141A 3 Pressure Relief Procedure 1. Turn power switch OFF and unplug sprayer power cord. 2. Turn spray/prime valve to PRIME to relieve pressure. 3. Hold metal part of gun firmly to side of a grounded metal pail. Trigger gun. 4. Engage trigger lock. If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved after following the steps above, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Clear hose or tip obstruction. Trigger Lock Always engage the trigger lock when you stop spraying to prevent the gun from being triggered accidentally by hand or if dropped or bumped. Installation 1. Follow pressure relief procedure. 2. Prime pump (refer to your sprayer operation manual for this procedure). 3. Install roller frame. Follow this Pressure Relief Procedure when you stop spraying and before cleaning, checking, servicing, or transporting equipment. .............. .......... ................ .............. Do not modify the extension tube or roller frame or use parts not designed for this equipment. Gasket (12) must be in place before installing frame (1). If gasket is not in place there is a potential injection hazard which could result in serious injury. Refer to your sprayer and spray gun instruction manuals for safe operation of this frame. .............. Cleaning This is the procedure for flushing/cleaning the pressure roller. The sprayer and gun you are using may have additional flushing/cleaning instructions; such as cleaning filters and screens. See sprayer and gun operation manuals. • Leave pressure roller attached to gun for this procedure. • Refer to roller parts drawing, page 1. Relieve pressure, page 3. 2. Remove roller cover (19) and diffuser (23) from roller frame (1) as follows: a. Using your thumb, press down on clip (5) to release end caps (3 & 9), diffuser, (23) and roller cover (19) into pail. b. Remove roller cover (19) from diffuser (23). Cleaning c. Pull end caps (2 & 4) off diffuser (23). 3. Clean roller cover (19), caps (2 & 4) and diffuser (23) with water or a compatible fluid for oil-based materials. 4. Place roller frame (1) in paint pail. Be sure the holes in roller frame (1) are facing inside paint pail. 5. Prime pump with water or flushing fluid for oil-based materials. Use the lowest pump pressure setting. 6. Turn prime/spray valve to SPRAY. Perform Step 7 at the lowest pressure possible. 7. Trigger gun until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of roller frame (1) is clear. 9. Shut off pump. Turn prime/spray valve to PRIME. 311141A Parts Parts Qty. 1 1 1 1 1 1 1 1 2 ................ 4 1 5 9 ...
Dieses Handbuch ist für folgende Modelle:Andere Werkzeuge - 311141A (313.47 kb)