Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Be sure the breather valve is open. If this does not correct the problem see strainer tube assembly paragraph. TIRE PRESSURE FOR SHIPPING PURPOSES, THE TIRES ON YOUR UNIT MAY BE OVER-INFLATED. TIRE PRESSURE SHOULD BE REDUCED BEFORE UNIT IS PUT INTO OPERATION. RECOMMENDED PRESSURE SHOULD BE APPROXIMATELY 15 P.S.I. EQUAL TIRE PRESSURE SHOULD BE MAINTAINED ON ALL TIRES. MAXIMUM TIRE PRESSURE IS 30 P.S.I. A CAUTION Installation of tire to rim: 1. Lubricate tire beads and rim flanges. 2. Do not exceed 30 P.S.I. when seating beads. 3. Adjust to recommended pressure after beads are sealed. HEX LOCKNUT /«it STROKE RETURN STOP PLUNGER 8M HEX BOLT FIGURE 26 NOTE When the pressure relief valve opens a loud high pitched sound is heard and engine labors. HOSE CLAMPS Check the hose clamps on the bottom of the pump for proper tightness before each use. Hose clamps on the return hose should be checked once a season. STRAINER TUBE ASSEMBLY If the ram does not move back and forth smoothly the strainer tube assembly may be clogged. To clean follow these steps. 1. Remove the hose clamp at inlet hose {bottom hose on rear of beam). STROKE RETURN STOP PLUNGER If the engagement handle does not return to neutral (from reverse) before the pressure relief bypass opens, loosen the hex locknut, back out hex bolt one or two turns. See figure 26. 12 NOTE Be prepared to catch oil in some container. Pull off inlet hose from strainer tube assembly and catch oil in a suitable container. See figure 27. 3. With an adjustable wrench remove the strainer tube assembly. See figure 27. 4. Clean and reassemble using a hydraulic pipe sealant on the threads. PRESSURE RELIEF VALVE SETTING FIGURE 28 Check oil in log splitter reservoir before every use. See figure 29. 1. Block up front of log splitter so beam is setting level. 2. Remove check pipe plug in rear of beam. See figure 29. If oil starts to come out of check pipe plug hole oil level is correct. IF NOT add oil to breather tube (figure 16) unit oil starts out. NOTE Use hydraulic sealant tape or pipe sealant on pipe plut threads. 3. Replace check pipe plug, remove block from under front of beam. NOTE The strainer tube assembly is 53" long. If the pressure relief valve is set too low it will open up before enough pressure is built up to properly operate the ram. See figure 28. TO SET THE PRESSURE RELIEF VALVE 1. Have someone place a log crossways in the Splitter and allow the Ram to push against it with the engine running wide open 2. If the engine begins to lug down, the Relief Valve setting is correct. 3. If adjustment is necessary, tighten the screw until the engine begins to lug down. 13 FIGURE 29 ENGINE MAINTENANCE REFER TO ENGINE MANUAL. STORAGE INSTRUCTIONS In event engine is to be stored for any length of time (30 clays or more), prepare as follows: 1. Drain gasoline by tipping or by syphon hose, then run engine until remainder is used and tank and carburetor are empty. A CAUTION Drain into container outdoors away from fire or flame. 2. Drain carburetor by running engine until it stops. 3; Inside protecting of engine for storage is performed by removing spark plug and pouring one ounce of SAE 30 oil through spark plug hole into cylinder. Crank engine, without starting, several times to spread oil over cylinder walls. 4. Never store outside without a waterproof cover. 14 NOTES '*■ 15 24645-9 16 PARTS LIST FOR LOG SPLITTER MODEL NO. 24645-9 Ref. No. Part I Color No. j Code Description New Part Ref. No. Part No. Color Code Description New Part 1 727-0211 Forward stroke high 32 13747 Frame Ass'y- N pressure hose 33 710-0409 Hex Scr. 5/16-24 x 1.75" 2 727-0212 Return stroke high L9-* pressure hose 34 750 0442 Spacer .75" I.D. x 1.12' 3 710-0106 Hex Scr. 1/4-20 x 1,25" Lq.* O.D. x 1.56” Lg. N 4 737-0160 Breather Plug 35 714-0121 Cotter pin 5/32" Dia. x 5 737-0153 Return Elbow 1.00" Lg.* 6 726-0173 Hose Clamp 36 734-0873 Hub Cap (Service Only) 7 727-0210 Return Hose 3/4" I.D. x 37 712-0299 Hex Castle nut 3/4-16 Thd. 2.62" Lg. 38 741-0107 Tapered roller bearing 8 717-0406 Cylinder Assy. 4.0" Dia. (Service Only)' x .24" stroke N 39 734-0871 Wheel Rim Ass'y- 9 08118 Grip (Service Only) 10 747-0289 Cylinder Support Rod 40 734-0872 Tire only 4.80/4.00 x 8 11 736-0119 L.-Wash. 5/16" Scr.* (Service Only) 12 712-0267 Hex Nut 5/16-18 Thd.* 41 734-0870 Wheel Ass'y- Comp. 13 13743 Complete oil tank & 4.80/4.00 x 8 Beam Ass'y. N 42 736-0119 L-Wash. 5/16" Scr.* 14 13677 Strainer Tube Ass'y- 50" Lg. 43 712-0123 Hex Nut 5/16-24 Thd. 15 710-0624 Hex Scr. 5/16-24 x 1.50“ 44 727-0215 Inlet hose 3/4" I.D. x Lg.* 14" Lg. N 16 712-0123 Hex Nut 5/16-24 Thd.* 45 750-0426 Pump Inlet Tubing 17 736-0159 Fl.-Wash. .34 I.D. x .88 46 736-0119 L-Wash. 5/16" Scr.* O.D. 47 710-0157 Hex Scr. 5/16-24 x .75" Lq.* 18 732-0253 Compression Spring ...
Dieses Handbuch ist für folgende Modelle:Andere Werkzeuge - 24645-9 (851.41 kb)