Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Step 1. Preparation Connect the phone to perform basic configurations Connect an analog phone to the FXS port of IPC 1000 series unit as the picture below and power on. Please notices that do not connect phone line of the telephone company to the FXS port as doing so may cause damage to the product! Connect a phone to the IPC 1000 series unit Step 2.Configure Region ID Skip this step if you are installing your IPC 1000 series unit in the default region. The default Region ID is printed on the label located outside the box. If you are installing your IPC 1000 series unit at any region other than that which is specified, you will need to configure the IPC 1000 series unit to the correct Region ID. Region ID The Region ID is coded as follows: ID NO. Country ID NO. Country ID NO. Country ID NO. Country 01 Argentina 02 Australia 03 Philippines 04 Portugal 05 Brazil 06 Canada 07 China 08 Russia 09 Sweden 10 Vietnam 12 France 13 Germany 15 Hong Kong 18 India 22 Italy 23 Japan 24 Korea 26 Malaysia 27 Mexico 28 Netherlands 29 New Zealand 36 Singapore 38 Slovenia 39 South Africa 40 Spain 42 Switzerland 43 Taiwan 44 Thailand 46 British 47 USA 60 Iran 61 Dubai (Note: If your Region ID is not listed on the chart above, please refer to the IPC 1000 series User’s Manual) Using a phone to configure the region ID 1. Pick up the phone and press 2. ##0000 You will hear 3 short tones. 3. 9507# Assuming you are modifying for China, the last 2 digits “07” are China’s regional ID. 4. 971# Enable the new region ID. (This action will change all setting values to return to their default values) 5. Hang up the phone The configuration procedure depends on the way you get the IP address, static IP, DHCP and PPPoE. According to the network condition, you can select one of them to do the configuration. Using a phone to configure basic information 1. Pick up the phone and press 2. ##0000 You will hear 3 short tones. 3. 012# The number “2” represents the Taipei area code. 4. 0282261111# The phone number is 82261111 1. Static IP Address Step 3.Configure Phone number, IP address and WEB password 5. 030# Enable “static” IP mode. 6. 04210*62*149*250# Configures the IP Address “210.62.149.250”. 7. 05255*255*255*128# Configures the Subnet Mask “255.255.255.128”. 8. 06210*62*149*254# Configures the Default Gateway “210.62.149.254”. 9. 882834# The numbers ”2834” in this string are the web based management password. 10. 981# Restarts. (The system should be restarted immediately) 11. Hang up the phone Note: This is the area code of the phone number. For example, “2” for Taipei, “21” for Shunghai, “10” for Peking and “408” for San Jose (USA). 2. DHCP Mode If want to setting the DHCP mode to get an IP, please follow the actions: Using a phone to configure basic information 1. Pick up the phone and press 2. #0000 You will hear 3 short tones. 3. 012# The number “2” represents the Taipei area code. 4. 0282261111# The phone number is 82261111 5. 031# Enable “DHCP” IP mode. 6. 882834# The numbers ”2834” in this string are the web based management password. 7. 981# Restarts. (The system should be restarted immediately) 8. Hang up the phone 3. PPPoE Mode PPPoE modes use dynamically assigned IP addresses and because of this there are difficulties with regards to Web based management. We strongly suggest that you use a private and fixed IP address such as 192.168.0.2 (default setting) so that you can use the web based interface to configure the IPC 1000 series unit’s other advanced configurations. 1. Using a phone to configure information 1. Pick up the phone and press 2. ##0000 You will hear 3 short tones. 3. 012# The number “2” represents the Taipei area code. 4. 0282261111# The phone number is 82261111 5. 04192*168*0*2# Configures the IP Address “192.168.0.2”. 6. 05255*255*255*0# Configures the Subnet Mask “255.255.255.0”. Note: If the IPC 1000 series unit’s IP address has been set to public or static IP mode; you must configure the IP Address and Subnet Mask of the PC to be in the same subnet as the IPC 1000 series unit rather than using IP address “192.168.0.5” and Subnet Mask “255.255.255.0” as the above illustration demonstrates. 3. Entering the Web Based Management Interface The IPC 1000 series unit’s IP address Fill in”WEB” (all capitals) and the password that you have configured in the basic configuration section Press the “OK” button 4. Configuring the IPC 1000 series unit’s IP Modes using the Web Based Interface Note: If you need to configure any other parameters after the IP mode configuration is done, do not restart the IPC 1000 series unit as it will use the new IP setting. When this happens, you may no longer be able to access the IPC 1000 series unit using a web browser. You will then need to use a phone or console to configure the IP back to its default or fixed IP address such as “192.168.0.2”. 4. Click the “Apply” button to apply any 3. Enter the PPPoE information. 1. Select BASIC Button. 2. Select PPPoE Fill in the (PPPoE) account username...