Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Use a screwdriver to loosen the screw and remove the front of the sensor. 2. Insert two AAA batteries (not supplied). 3. After you replace the batteries, place the magnet next to the sensor then move it away. If the system does not chime, you must register the sensor again. To register the sensor, follow steps 1 thru 6 on page 1. If the sensor stops working properly, or PROBLEM appears on your console’s display, replace the sensor’s batteries. • Dispose of old batteries promptly and properly. Do not burn or bury them. • Use only fresh batteries of the required size and recommended type. • Do not mix old and new batteries, different types of batteries, or batteries of different capacities. initializing your sensor49-1001 Wireless SecurityDoor/Window Sensor This wireless door/window sensor only works with your Wireless Security Kit (49-1000). Your Wireless Security Kit includes two sensors. Purchase up to 28 additional (30 total) sensors to expand and protect all 30 system zones. You can add additional door/window sensors and additional motion detectors, as long as the additional units do not exceed 30 (number of zones in your system). Refer to your 49-1000 user guide for more information on adding motion detectors and door/window sensors to your wireless system. The sensor jack allows you to hardwire an extra magnetic switch for additional door/ window protection.The sensor must be within 100 feet of the console to operate properly. 1. Press and hold down TEST on the sensor for 3-4 seconds, and then release it. The green LED blinks twice. Note: If you need to register the sensor a second time, remove the batteries, and then hold down TEST for 3-4 seconds to pick up a random code. 2. Replace the cover. 3. Place the magnet next to the sensor, with their arrows aligned. 4. Press menu start or on your system console. ENTER PIN (Personal Identification Number) appears on the display. 5. Use the console keypad to enter your four- digit PIN. * appears on the display as you press each digit. After you enter your PIN, 1. INSTALL appears. 6. Press ok and 1. INSTALL / ZONE appears. 7. Move the magnet away from the sensor. The console chimes and ZONE 1 SET appears on the display to confirm registration. 8. Press clear to navigate backwards through the console menu options. Press 1 to return to the main display, press 2 to stay in install mode and register additional sensors. registering your sensorTEST . . DELAY MIN/MAX wall anchors (2) screws (2) magnet sensor . . . . Please read this user’s guide before installing, setting up and using your new product sensor magnet screws (2) wall anchors (2) what’s included 1. Use a screwdriver to loosen the screw and remove the front of the sensor. 2. Insert two AAA batteries (not supplied). 3. After you replace the batteries, place the magnet next to the sensor then move it away. If the system does not chime, you must register the sensor again. To register the sensor, follow steps 1 thru 6 on page 1. If the sensor stops working properly, or PROBLEM appears on your console’s display, replace the sensor’s batteries. • Dispose of old batteries promptly and properly. Do not burn or bury them. • Use only fresh batteries of the required size and recommended type. • Do not mix old and new batteries, different types of batteries, or batteries of different capacities. initializing your sensor49-1001 Wireless SecurityDoor/Window Sensor This wireless door/window sensor only works with your Wireless Security Kit (49-1000). Your Wireless Security Kit includes two sensors. Purchase up to 28 additional (30 total) sensors to expand and protect all 30 system zones. You can add additional door/window sensors and additional motion detectors, as long as the additional units do not exceed 30 (number of zones in your system). Refer to your 49-1000 user guide for more information on adding motion detectors and door/window sensors to your wireless system. The sensor jack allows you to hardwire an extra magnetic switch for additional door/ window protection.The sensor must be within 100 feet of the console to operate properly. 1. Press and hold down TEST on the sensor for 3-4 seconds, and then release it. The green LED blinks twice. Note: If you need to register the sensor a second time, remove the batteries, and then hold down TEST for 3-4 seconds to pick up a random code. 2. Replace the cover. 3. Place the magnet next to the sensor, with their arrows aligned. 4. Press menu start or on your system console. ENTER PIN (Personal Identification Number) appears on the display. 5. Use the console keypad to enter your four- digit PIN. * appears on the display as you press each digit. After you enter your PIN, 1. INSTALL appears. 6. Press ok and 1. INSTALL / ZONE appears. 7. Move the magnet away from the sensor. The console chimes and ZONE 1 SET appears on the display to confirm registration. 8. Press clear to navigate backwards through the console menu options. Press 1 to return to the main d...