Use care to differentiate rear crossbar (B) (341/2" long) from footrest crossbar (C) (351/2" long). Attach both rear crossbars (B) and the footrest and support crossbars (C) to one side frame (A) using 2" Allen bolts (H). Tighten securely. Note: Threaded barrels preattached to leg frames must be in rear and facing out. Attach other side frame (A) to opposite ends of crossbars in step two using 2" Allen bolts (H). Tighten securely. Place dust cover (D) over top of base frame and attach using %

Use care not to drill all the way through the tabletop. ^5 Attach front hinges and rear brackets to tabletop using %" Phillips screws (I). Tighten securely but use care not to over tighten and strip. ©2008 ALVIN & COMPANY, INC. • P.O. Box 188, Windsor, CT 06095-0722 WWW.alvinCO.COm Phone: 860-243-8991 • Toll-Free: 800-444-2584 • Fax: 860-242-8037 • Toll-Free Fax: 800-777-2896 lit-abiss 7/qb

XII-4-XB Tools Required: Phillips screwdriver, drill with VW bit. Parts Included: A 1pc Leg Frame B 1pc Tabletop C 2pcs Rear Extension Tubes (Shipped in separarate box) : D 2pcs Front Extension Tubes F 2pcs Height Adjustment Knobs To Assemble: Unpack all parts and inspect to confirm that all are present. Unfold base (A). Insert rear extension tubes (C) completely into frame (A) and loosely hand-tighten knobs (F). Insert front extension tubes (D) into frame (A). Place table top (B)

Hinges should also be centered evenly between left and right sides of tabletop. ^3 Adjust and position rear mounting brackets so they are 19/" from the front edge of the table top and centered evenly between left and right sides, as shown in diagram. Brackets should sit flush on the tabletop surface with the rods facing straight up and down. ^4 Mark locations of all 12 holes with a dark pencil or marker and then use an awl or drill with 1/i6" bit to make starter holes. Use care not to drill al

WTF35 B C E CONTENTS Key Qty. Description A 1 Grid Tray with small openings B 1 Frame Section with rubber feet C 2 Grid Tray with large openings D 1 Frame Section E 2 Covered Casters with lock nuts F 2 Side Braces (left and right) G 1 Dust Protector bottom cover (Optional) 12 Nuts, 4 Screws 1. Attach grid tray with small openings(A), to bottom of large frame section(B). 2. Attach remaining two trays(C). 3. Secure smaller frame section(D) in the same manner. 4. Using encl

Align holes in front leg extensions (D) with holes in table top as shown in Figure 1. Fasten all 1/2" screws (H) and tighten securely. Use care not to overtighten and strip. Carefully return table assembly to the upright position. Adjust table top to desired height using height adjustment knobs (F). You’re finished and your table is ready to use as shown in Figure 2. Folding Table: Drop all extension tubes down to their lowest positions. Lift top up until the front extension tubes (D) diseng

Lumens Tubes Lumens at per Tube per Box Light Box Surface LB1218 650 1 F15T8 650 LB1620 650 2 F15T8 1300 LB1824 650 2 F15T8 1300 LB2436 1750 3 F30T8 5100 All electrical components are U.L. listed. 4. Remove the hold-down screws and lift off the light diffusers. 5. Remove and replace fluorescent tubes. 6. Return diffusers, glass and Plexiglas panels to their original positions. Re-install aluminum strips and screws. T y Alvin & Company, Inc. Bloomfield, CT Grand Prairie, TX www.a

For your own safety, use gloves when handling glass. Place the glass on top of the Plexiglas sheet and replace the aluminum strips. 2. To operate, depress the on/off switch and hold for one or two seconds until the lights illuminate. Note: Bulbs may loosen during shipping. If bulbs don't illuminate check that they are properly seated in fixture. 3. The Satin-Glow Lightbox is designed to operate on 110V AC, 60 cycle. Please do not use any other power source. 4. Removal of the back panel or tam

Make sure ends of back panel are snug against steel leg frames and holes are aligned in steel flange with pre-drilled holes in back panel. Attach using four 5/s" screws (I) supplied. Repeat step for right leg frame. Figure 2 5/s" Screws Floor Glide Figure 1 5/s" Screws □ Carefully remove base assembly from table/bench and place upright on floor. ^9 Place shelf (D) with predrilled holes facing up on the bench/table with 15 ends hanging over edge. Lift base assembly carefully (may require

WSF36 CONTENTS Key Qty. Description A 2 Large Side Grids Back Grid B 1 C 2 Center Grids D 1 Front Grid E 1 Bottom Step F 4 Casters G 1 Bag Small Clips H 1 Bag Large Clips F NOTE: Plastic clips can be snapped on and removed easily by hand. Most grid sections require only 2 clips per side for support. For safety, clips attached on exterior of cart should be positioned with flanges facing inward. (See reverse side for assembly) CLIP ATTACHMENT TAIWAN Assembly Instructions for No