Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Atlas Dateigröße: 476.77 kb Dateiname: 598-1094-01.pdf Unterrichtssprache:

• Automatically turns lighting off. • Dual Light Level • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Sensor Lamp Holders (3 sizes included) 2 Shells Light Control 6 Screws Cover Plate 2 Wire Connectors Mounting Bolt Gasket Mounting Strap Rubber Plug Plastic Hanger Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qualified electrician. • This product is intended for use with the enclosed gasket and with a junction box marked for use in wet locations. OPERATION Mode: On-Time: Works: Day Night Test 5 Seconds x x Auto 1, 5, 20 min. x Manual Until Dawn* x Accent 3, 6 Hr, to Dawn x * resets to Auto Mode at dawn. Note: When first turned on wait about 1 1/2 minutes for the circuitry to calibrate. TEST TEST 1 5 20 ON-TIME Off 36 Dusk to Dawn DUAL LIGHT LEVEL Put ON-TIME switch on the sensor bottom to TEST and the Dual Light Level switch OFF. AUTO ON-TIME 20 5 1 TEST Put the ON-TIME switch in the 1, 5, or 20 minute position. MANUAL MODE Manual mode only works at night because daylight returns the sensor to AUTO. Flip the light switch off for one sec 1 Second OFF ond then back on to toggle between then... AUTO and MANUAL MODE. Manual mode works only with the ON-TIME switch in the 1, 5, or 20 position. ... back on. Mode Switching Summary TEST Move ON-TIME Switch to 1, 5, or 20 minutes AUTO Flip light switch off for one second then MANUAL MODE back on* * If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control will be in the AUTO mode. Dual Light Level Control Light comes on half bright for selected time after dusk (Off, 3 hr., 6 hr., until dawn). If motion is sensed, the light turns on full bright for the ON-TIME (1, 5, or 20 minutes) then returns to dim mode. 240-028-A © 2003 Atlas Lighting Products, Inc. 598-1094-01 INSTALLATION For easy installation, select an existing light with a wall switch for replacement. 123456789012345678912345678901234567891234567890123456789 Wall Mount Eave Mount For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock. For eave mount only: . Swing the sensor head towards the clamp screw joint. Controls Clamp Screw . Then rotate the sensor head clockwise 180° so the controls face down. Controls Controls If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done. MOUNT THE LIGHT CONTROL. White to White Black to Black Junction box ground wire to green ground screw on fixture. Gasket Mounting Strap Mounting Bolt Rubber Plug . Align the Light Control cover plate and cover plate gasket. Secure with the mounting bolt. . Align the three slots in the decorative shell with the lamp holder pins. Push the shell in and then twist clockwise to lock. Repeat for other shell. Shell Slot . Push the Rubber Plug firmly into place. . If a wet location junction box was not used, caulk the wall plate mounting surface with silicone weather sealant. To avoid water damage and electrical shock, keep lamp holders 30° below horizontal. WIRE THE LIGHT CONTROL. . Turn power off at the fuse or circuit breaker. . Remove the existing light fixture. . Install the mounting strap as shown using two screws that fit your junction box. . The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap. . Route the Light Control’s wires through the large gasket holes. . Twist the junction box wires and fixture wires together as shown. Secure with wire connectors. Lock Nut Keep lamps at least 1" (2.5 cm) from the sensor. Do not allow the lamps to Lens block the lens. . Adjust the lamp holders by loosening the lock nuts but do not rotate the lamp holders more than 180° from the factory setting. When screwing in the floodlamps, do not overtighten. 598-1094-01 -2 TEST AND ADJUSTMENT . Turn on the circuit breaker and light switch. NOTE: Sensor has about 1 1/2 minutes warm up period before it will detect motion. When first turned on, wait about 1 1/2 minutes. . Turn the RANGE control to the mid position, DUAL LIGHT LEVEL to OFF, and the ON-TIME control to the TEST position. BO O S T MAX MIN RANGE ON - TIME TEST 1 5 2 0 MINUTES OFF 3 6 DUSK TO HOUR DAWN DUAL LIGHT LEVEL Bottom of Sensor Avoid aiming the control at: • Objects that change temperature rapidly, such as heating vents and air conditioners. These heat sources could cause false triggering. • Areas where pets or traffic may trigger the control. • Nearby large, light-colored objects reflecting light may trigger the shut-off feature. Do not point other li...

Herunterladen

Geben Sie zwei Ziffern: