Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Agri-Fab Dateigröße: 439.54 kb Dateiname: 45-02171.pdf Unterrichtssprache:

FT. (SUPER 17) • Assembly • Operating •Maintenance •Repair Parts 303 WEST RAYMOND • SULLIVAN, ILLINOIS 61951 PRINTED IN U.S.A FORM NO. 46085 (Rev. 11/94) ASSEMBLY INSTRUCTIONS Contents of Hardware Pack (See figure 1) REF. QTY. DESCRIPTION A 2 Tube Spacer 1-1/4" O.D. x 2" Lg. B 2 Pin, Cotter 1/8 x 1-1/2” Long C 2 Hex Nut 3/8 Thread D 4 Washer, Flat 1.032 I.D. E 2 Hub Cap F 23 Hex Bolt 1/4 x 1/2" Long G 6 Hex Bolt 1/4 x 5/8" Long H 6 Hex Bolt 1/4- 3/4" Long I 2 Lock Washer 3/8" I.D. J 2 Hex Bolt 1/4 x 1-3/4" Long K 37 Lock Washer 1/4" I.D. L 37 Hex Nut 1/4" Thread M 8 Hex Bolt 5/16 x 3/4" Long N 8 Lock Nut 5/16" Thread 0 14 Slotted Truss Head Bolt 5/16" x 3/4" 14 Long P Lock Washer 5/16" I.D. Q 14 Hex Nut 5/16" Thread R 2 Hex Bolt 3/8" x 1" Long IDENTIDICATION OF LOOSE PARTS (See figure 2) note Wheels (Al) are packed in a separate carton). LOOSE PARTS (See figure 2) V Tailgate W Cart Body (2) X Tailgate Guides Y Corner Caps Z Front Panel AA Draw Bar Tongue AB Wheel Support AC Wheel Axle Brackets AD Axle AE Tailgate Reinforcement Bracket AF Latch Stand Bracket AG Latch Lock Sub-Assembly AH Hitch Bracket Al Wheels 2 1. Remove the hardware pack and all loose parts from the carton. Be sure carton is empty before discarding. 2. Layout all the parts as shown in figure 2. A CAUTION To help prevent tipping of cart, assemble on a smooth level surface such as a garage floor or a paved driveway. Pay close attention to stability of the cart body when it is in an upright position. DO NOT LEAVE THE CART UNATTENDED IN UPRIGHT POSITION. The cart could be knocked over causing personal injury or damage to the cart. 3. Position the cart body halves (W) upright, on a smooth level surface, as shown in figure 3. 4. Assemble the bolts (F), the lock washers (K) and hex nuts (L) to the holes in center flanges. Do not tighten till step 15, page 5. See figure 3. 5. Position the wheel support (AB) in place on the bottom of the cart. See figure 4. 6. Assemble wheel support to cart with eight slotted head screws (O) lock washers (P) and hex nuts (Q). The heads of the screws should go to the inside of the cart bed as shown in figure 4. These screws should be tightened after they are all assembled. POSITION CART BODY HALVES WITH LARGER DIAMETER HOLES AT TOP LOCK WASHERS (K CENTER FLANGES HEX BOLTS (F) FIGURE 3 FIGURE 4 3 7. Position the tailgate reinforcement bracket (AE) over end of cart. See figure 5. 8. Start slotted screws (0) through bottom of cart (heads of screws to the inside of cart) and reinforcement bracket. Secure finger tight with hex nuts (Q) and lock washers (P). See figure 5. 9. Position the tailgate guides (X) so that the holes line up with reinforcement bracket and cart body. Refer to tailgate guide detail in figure 5. 10. Secure tailgate guides with six hex bolts (H) lock washers (K) and hex nuts (L). See figure 5. Tighten bolts assembled in steps 7, 8 and 9 at this time. Do not tighten others. STAND CART ON TAILGATE REINFORCEMENT BRACKET FIGURE 6 11. Reverse the cart position and stand on tailgate reinforcement bracket and proceed with assembly steps 12 through 20. See figure 6. 12. Assemble front panel to open end of cart body, using 1/4" x 1/2" hex bolts (F), lock washers (K) and hex nuts (L). Bolt heads to inside of cart. Leave out (2) bolts for latch stand bracket. See figure 7. FIGURE 5 FIGURE 7 13. Assemble latch stand bracket using four 1/4" 16. Assemble wheel axle brackets (2) to wheel x 5/8" hex bolts (G), lock washers (K) and hex support, using 5/16" x 3/4" hex bolts (M) and nuts (L). See figure 8. lock nuts (N). NOTE: Place welded tubes to middle, as shown in figure 10. 14. Assemble two front top corner caps and two bolts in top flanges through tailgate reinforcement bracket using 1/4" x 1/2" hex bolts (F), lock washers (K) and hex nuts (L). See figure 9. 15. Tighten all bolts assembled in step 4 through 14, lower cart assembly to rest on top flanges, with axle support up. See figures 10 and 13. 17. Assemble latch lock subassembly to drawbar tongue using 1/4" x 5/8" long hex bolt (G), lock washers (K) and hex nuts (L). See figure 11. FIGURE 9 5 FIGURE 11 18. Assemble hitch bracket to drawbar tongue, using 3/8" x 1" long hex bolts (R), lock washers (I) and hex nuts (C). See figure 12. 19. Assemble axle, (2) tube spacers and draw bar tongue to wheel support keeping open side of tongue facing up, make sure that latch lock ...

Herunterladen

Geben Sie zwei Ziffern: