Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The unit will turn on automatically at dusk, operate through the night and turn off in the morning. 4. Select the proper location to hang your unit as described above and hang the unit approximately 7 feet above the ground from a tree, mounting pole or other free standing object. Never mount the unit from house or other building. 5. Plug cord into a compatible extension cord rated for outdoor use. 6. This unit is designed to withstand moderate rains but should be taken down and stored indoors during severe weather. 7. It is recommended that this unit be put into use in early spring and left out until late fall to maximize effects. INSTALLING THE NOSQUITO BY STINGER MOSQUITO ATTRACTANT Use only NOsquito™ by Stinger ® lures. You will find a NOsquito™ octenol lure (NS16) included with the Stinger ® Mosquito Killer. Research has shown that octenol is effective in attracting many species of mosquitoes and biting flies. This lure has slow release properties and increases the effectiveness of luring mosquitoes to the unit. For best results, replace every 30 days. 1. Remove lure from pouch. 2. Place lure in into black cassette and attach to body of the cage. (Fig. 4) (For best results, attach cassette to the upper part of the cage.) 3. To remove, simply discard cassette and lure appropriately in a trash receptacle. TROUBLESHOOTING Figure 4 Figure 5 CHANGING BULBS Use only Stinger ® replacement bulbs. This bulb (BB07) should be replaced annually to maintain optimal UV effectiveness. Even though the bulb’s light may be visible to you, its ability to attract mosquitoes diminishes over time. If the bulb fails to light or the color of the light changes to yellow or orange it is time to replace the bulb. (Fig. 5) 1 Unplug the unit and remove from hanging position. 2 With a Philips head screwdriver, open the front cage door by removing the screw. 3 Press the end of the bulb into the retainer ball so the bulb prongs fit under the socket. 4 Insert the new bulb making sure it is properly seated in the socket. 5 Shut the door until it securely snaps in place and replace the screw. 6 Place unit back into the hanging position and plug back into the outlet. 7 Note: the bulb in this unit contains Mercury, dispose according to Local, State or Federal Laws. CLEANING As the unit kills insects, most of the insect remains will be vaporized or fall down through the unit. Some remains may be left on the grids and over time will reduce the effectiveness of this device. Make sure to regularly clean your unit to achieve maximum effectiveness. The time in between each cleaning will vary depending on your insect populations. Check your unit frequently and clean any insect remains you see. (Fig. 6) 1. Unplug and remove entire unit from hanging position. 2. With a Phillips head screwdriver, remove the screw that secures bottom grid cover to body of unit. Expose the killing grid by opening the bottom grid cover. As the grid cover swings open, power to the killing grid will be stopped. 3. Using a small brush or stick, gently remove any insect remains from the grid. 4. If available, you may use compressed air to clean out your unit. 5. Never use water to clean your unit, water could damage the electrical components. 6. Once the unit is clean, snap the bottom grid cover back in place, return the unit to the hanging position and reconnect to power source. Note: If arcing occurs after cleaning, unplug unit and remove from hanging position. Check the grids and make sure they are not touching in any place. Gently use a stick to bend grids away from each other. Figure 6 COMO ESCOGER UNA UBICACION Al seleccionar una ubicacion, debe recordar que los mosquitos seran atraidos a la unidad de modo que no debe poner la unidad cerca de donde hay actividad humana. Escoja una ubicacion alejada unos 25 pies (xx m) del area que esta tratando de proteger. Si hay una fuente de agua cercana, coloque la unidad entre usted y el agua ya que el agua es un criadero para la mayoria de los mosquitos. El MK100 esta disenado para cubrir hasta 1/2 acre (xx m2). ( Ilustracion 1) StingerArbolesCharcaCasa25' Ilustracion 1 Ilustracion 3 Ilustracion 2 INSTALACION / OPERACION 1. Desempaque la unidad, guarde todos los materiales de empaque para almacenarla fuera de estacion. 2. Sujete el borde superior uniendo las dos mitades alrededor de la parte superior de la unidad. El logotipo de StingerMR debe estar en la parte frontal de la unidad, alineado con el Icono n...